Lab.gruppen FP+ series - Current Draw and Thermal Dissipation Specifications

30 FP+ Series Operation Manual
8 APPENDIX
8.5 Current Draw and Thermal Dissipation specifications
The following tables contain information on measured current consumption as well as calculated heat dissipa-
tion during normal operation(1/8 rated power); and during extreme heavy duty operation (1/4 rated power).
115 VAC 230 VAC In Out Dissipated BTU/hr kCal/hr
0 0 0 0 0
129 0 129 440 111
16 ! / Ch. 1200
x2
32 ! / Bridged 2400
x1
8 ! / Ch. 2350
x2
16 ! / Bridged 4700
x1
4 ! / Ch. 4400
x2
8 ! / Bridged 8800
x1
2 ! / Ch. 6500
x2
4 ! / Bridged 13000
x1
16 ! / Ch. 1200
x2
32 ! / Bridged 2400
x1
8 ! / Ch. 2350
x2
16 ! / Bridged 4700
x1
4 ! / Ch. 4400
x2
8 ! / Bridged 8800
x1
2 ! / Ch. 6500
x2
4 ! / Bridged 13000
x1
Mains connector, 230 V CE version
Mains connector, 115 V ETL version
FP 13000
Level
Load
Rated
Power
Line Current *2)
Watt *1)
Thermal Dissipation
993
3390
854
58,0
29,0
4243
3250
Pink noise
(1/4 rated
power) *3)
16,0
2933
486
1659
418
237
807
203
1567
273
933
235
48,3
24,1
3419
911
8,0
1037
27,2
13,6
1840
800
3109
783
37,8
18,9
2536
1625
Pink noise
(1/8 rated
power)
10,6
1100
756
2578
650
1289
325
1690
426
300
378
5,3
588
495
1856
Standby w. remote Power Off via NomadLink
Power On, Idling
Amp
W
678
16,2
8,1
1083
26,5
13,2
*3) Figures measured at maximum power before amplifier protection and limiter features are engaged. Typically this is between 1/4 and 1/3 of rated power. Note
that the max. power condition is very extreme and will not occur during normal operation. Also note that the mains breaker will not be tripped even if operation is
in excess of max. ratings.
16 A, CEE7
30 A, Nema L5-30P Twist lock
*1) The amplifier's PSU operates as a non-resistive load, so the calculation "Volts x Amps = Watts" would not be correct. Instead, measured and specified here
is what is known as the "Active Power" of the amplifier providing useful, real-world values of power consumption and heat dissipation.
*2) Current draw figures measured at 230 V. 115 V figures are 230 V figures multiplied by two.
115 VAC 230 VAC In Out Dissipated BTU/hr kCal/hr
0 0 0 0 0
92 0 92 316 80
16 ! / Ch. 730
x2
32 ! / Bridged 1460
x1
8 ! / Ch. 1450
x2
16 ! / Bridged 2900
x1
4 ! / Ch. 2800
x2
8 ! / Bridged 5600
x1
2 ! / Ch. 3500
x2
4 ! / Bridged 7000
x1
16 ! / Ch. 730
x2
32 ! / Bridged 1460
x1
8 ! / Ch. 1450
x2
16 ! / Bridged 2900
x1
4 ! / Ch. 2800
x2
8 ! / Bridged 5600
x1
2 ! / Ch. 3500
x2
4 ! / Bridged 7000
x1
Mains connector, 230 V CE version
Mains connector, 115 V ETL version
754
2574
649
39,4
19,7
3088
2333
Pink noise
(1/4 rated
power) *3)
19,6
1867
967
487
39,4
19,7
2705
838
2860
721
1070
270
489
1667
420
643
9,8
800
33,3
16,6
1455
313
2195
553
22,0
11,0
1518
875
Pink noise
(1/8 rated
power)
6,8
3,4
700
476
1625
409
781
197
363
329
1123
283
183
229
5,4
692
411
17,4
8,7
1176
10,8
Standby w. remote Power Off via NomadLink
Power On, Idling
Amp
W
16 A, CEE7
30 A, Nema L5-30P Twist lock
FP 7000
Level
Load
Rated
Power
Line Current *2)
Watt *1)
Thermal Dissipation
*1) The amplifier's PSU operates as a non-resistive load, so the calculation "Volts x Amps = Watts" would not be correct. Instead, measured and specified here
is what is known as the "Active Power" of the amplifier providing useful, real-world values of power consumption and heat dissipation.
*2) Current draw figures measured at 230 V. 115 V figures are 230 V figures multiplied by two.
*3) Figures measured at maximum power before amplifier protection and limiter features are engaged. Typically this is between 1/4 and 1/3 of rated power. Note
that the max. power condition is very extreme and will not occur during normal operation. Also note that the mains breaker will not be tripped even if operation is
in excess of max. ratings.