Functions description:
1-01 When on, the engine remains running after the hand brake has been pulled, ignition is off and the
doors are closed. While the engine running, lights are flashing, remote is displaying the remaining time of
engine running. You can set 1, 3 of 10 minutes of engine running.
1-02 When on, the alarm will try to start the car up at the pre-set time. The function requires activating the
function on the remote, setting the time of the start up and setting the reservation mode.
1-03 Setting the engine running time when remotely started.
1-04 When on, you can enter a 4-digit emergency code to cancel the alarm and open the car.
1-05 By choosing this option, you can set up the conditions for a reservation mode set-up. For reservation
mode setting to carried out, transmission must be in a neutral position, emergency brake pulled up with the
engine running. By turning ignition off the engine remains running and reservation mode will be set after
choosing the option in programming menu 1-05. When choosing option No.3, the alarm will arm. Option No.4
is legacy mode of reservation mode not necessary connect hand brake wire. When door is closed and
ignition is switched off, engine remains running until door opens and closes again. When alarm will arm,
reservation mode will be set. If door is opened and ignition is off, engine will be stopped without reservation
mode set up.
1-06 When on, alarm will warn of the door opened by flashing the lights.
1-07 You can set the time for heating in diesel cars. It is also possible to set the time during which the
alarm will keep the ignition and accessories on when remotely started.
1-08 When on, alarm will warn that the hood is open by flashing the lights.
1-09 you can choose the type of engine sensing.
- alternator – input 12V required immediately after the engine is started and less than 5V when turned off.
- revs – you can use the sensor’s impulses based on the revs. Use this option for CAN bus connection.
1-10 It allows you to enter the valet mode in two ways:
- simple access – by turning ignition on/off 3 times in row
- secure access – by turning ignition on/off 3 times in row and entering a 2-digit PIN code by the button on
the back side of RPS.
1-11 In case of using the IG kill function, the blocking output is – active (on -250mA) when armed, -
inactive during a remote starting and disarmed; in case of using the PANIC function when disarmed, the
output will be activated after 30 sec. In case of using the Start kill function, blocking output is – active when
armed and remotely started, - inactive when disarmed; in case of using the PANIC function when disarmed,
the output will be activated immediately.
1-12 It is possible to set up a delayed reaction to opened door contacts when turning on the alarm. The
function is supposed to be used with indirect closed doors scanning (from the roof light, etc.)
1-13 It allows you to deactivate a ultrasonic sensor by using remotely starts. After cancel remote start
ultrasonic sensor is activated again.
1-14 This function is available with CAN BUS Magicar module. In case of using the Read only function,
Magicar only read CAN information (open door, trunk, hood, lock/unlock with OEM remote, etc.)
In case of using the Read and Write function, Magicar can also control lock/unlock, lights and klaxon
except closing windows.
In case of using the Read, Write and close windows, Magicar can also close windows when armed.*
1-15 When option No.1 is chosen, after pressing button III system unlock the door, disarming and open the
trunk. When option No.2 is chosen, after pressing button III system only open the trunk, not unlock the door
and not disarming. Trunk input will be able trigger system when trunk is closed.
1-16 The function automatic rearming is possible to disable by option II – in this case after alarm disarming,
countdown will not start and alarm is not arming itself. If factory setting – option I is set, after alarm disarming
, countdown started and after 30 seconds alarm is activated again (if door is not open)
1-17 If option I is set, when trunk is open (alarm is disarmed), reservation mode is cancelled. If option II is
set, when trunk is open, reservation mode still exists.
1-18 The siren output can by selected for offered siren or for klaxon control.
1-19 Option Standard is dedicated for all vehicles with start procedure by key. Option for START button
is dedicated for vehicles with start procedure by OEM START button.
* See possible function Module CAN BUS Magicar in Table of functions depending on car type.
For remote start is recommended to use wire for hand brake input.
To Next Page
Loading...
