Magnetek Elevator Quattro DC - Page 175

M
Maintenance, General ........................................... 86
Mech Brk Hold logic input ...................................... 69
Mech Brk Pick logic input ...................................... 69
Menus ................................................................... 28
Module A,B IGBT ................................................ 103
Monitor Rev ......................................................... 103
Motor Contactor Connections .............................. 141
Motor Field Res parameter .................................... 47
Motor Field TC parameter ..................................... 47
Motor ID Flt ......................................................... 103
Motor ID parameter ............................................... 51
Motor Mode analog output .................................... 72
Motor Mode display value ..................................... 76
Motor Rotation user switch .................................... 5 8
Motor Side Power Data D2 Submenu ................... 76
Motor Speed display value .................................... 73
Motor Trq Lim logic output ..................................... 71
MS Bus Voltage display value ............................... 76
MS I Conn Off Flt ................................................ 103
MS Size Fault ...................................................... 104
MS-LS Mismatch Flt ............................................ 103
Mtr Data Fault ..................................................... 104
Mtr Overload ....................................................... 104
Mtr Overload logic output ...................................... 71
Mtr Rev Vlt Lim parameter .................................... 47
Mtr Settings Fault ................................................ 104
Multi-Step Speed Command Debounce ................ 45
Multi-Step Speed Command Selection .................. 45
N
No Drv Handshake .............................................. 104
No Field Cable Flt................................................ 105
No Function logic input .......................................... 69
No Function logic output ........................................ 71
Not Alarm logic output ........................................... 71
Notch Filt Depth parameter ................................... 39
Notch Filter ............................................................ 42
Notch Filter Frq parameter .................................... 3 9
O
Open Armature Flt ............................................... 105
Ospd Test Src logic input ...................................... 69
Overcurr Flt ......................................................... 105
Overcurr Flt logic output ........................................ 71
Overspd Test Src user switch ............................... 60
Overspeed Flt ...................................................... 105
Overspeed Flt logic output .................................... 7 1
Overspeed Level parameter .................................. 35
Overspeed Mult parameter .................................... 35
Overspeed Time parameter .................................. 35
Overtemp Flt ......................................................... 92
Overtemp Flt logic output ...................................... 71
Overvolt Flt .......................................................... 106
Overvolt Flt logic output ......................................... 71
Ovld Start Level parameter ................................... 52
Ovld Time Out parameter ...................................... 52
OVLD TIME OUT parameter ................................. 54
Ovrtemp Alarm logic output ................................... 71
P
Parameter Reference .......................................... 3–9
Parameter Tree ......................................... 28, 31–32
PCU Data Flt ....................................................... 106
Phase Fault logic output ........................................ 71
PI Speed Regulator ............................................... 66
PLL Filter FC parameter ........................................ 50
Pole Filter parameter ............................................. 50
Pre Chge Thresh parameter ................................. 50
Pre Torque Time parameter .................................. 36
Pre-Torq Last display value .................................. 73
PreTorque Latch user switch ................................ 59
PreTorque Ref analog output ................................ 72
Pre-Torque Ref display value ................................ 73
PreTorque Source user switch .............................. 58
Pre-Trq Latch logic input .....................................
.. 69
Priority Message user switch ................................ 62
PTorq Latch Clck user switch ................................ 59
PWM Freq parameter ............................................ 48
R
Ramp Down En Src user switch ............................ 60
Ramp Down Ena logic output ................................ 71
Ramped Stop Sel user switch ............................... 60
Ramped Stop Time parameter .............................. 34
Rated Motor Curr parameter ................................. 51
Ready 2 Start logic output ..................................... 71
Ready to Run logic output ..................................... 7 1
Ready, Waiting for Drive ..................................... 106
Regen Trq Lim logic output ................................... 71
Relay Coils ............................................................ 70
Response parameter ............................................. 33
Reversed Tach Fault ............................................. 93
Run Command Src user switch ............................. 56
Run Commanded logic output ............................... 71
Run Confirm logic output ....................................... 71
Run Delay Timer ................................................... 38
Run Delay Timer parameter .................................. 38
Run Down logic input ............................................ 69
Run logic input ...................................................... 69
Run Up logic input ................................................. 69
RX Logic Input display .......................................... 75
S
Save Field Res parameter .................................... 53
Save Field TC parameter ...................................... 53
Save IR Drop parameter ....................................... 53
Save Meas Arm L parameter ................................ 53
Save Meas Arm R parameter ................................ 53
S-Chain Event ..................................................... 106
S-Curve Abort user switch .................................... 62
S-Curve Sel logic input .......................................... 69
Selecting Logic Input Definitions ........................... 68
Ser2 Insp Ena logic input ...................................... 69
Serial Link Follower ............................................... 25
Set-Up And Tuning Of Anti-Rollback ................... 113
Setup Flt .............................................................. 107
SFT CN NOT CLOSED fault ............................... 108
SFT CN OPENED fault ....................................... 107
Solid State Relays ................................................. 70
Spd Command Bias parameter ............................. 36
Spd Command Mult parameter ............................. 36
Spd Command Src user switch ............................. 56
Spd Dev Hi Level parameter ................................. 36
Spd Dev Lo Level parameter ................................ 35