– User and Installation Manual
TABLE OF CONTENTS
1 SAFETY INSTRUCTIONS ............................................ 3
1.1 General ................................................... 3
1.2 Warnings regarding the use of batteries .. 4
1.3 Location ................................................... 5
1.4 Connections ............................................ 5
1.5 Warning regarding life support
applications ............................................. 5
2 GENERAL INFORMATION .......................................... 6
2.1 Liability .................................................... 6
2.2 Warranty .................................................. 6
2.3 Identification label .................................... 6
2.4 Correct disposal of this product ............... 6
3 PRODUCT DESCRIPTION ........................................... 7
3.1 Overview of the connections .................... 7
3.1.1 Models 1500W, 2000W, 3000W ............ 7
3.1.2 Models 3500W, 4500W, 5000W ............ 8
3.2 Operating modes ..................................... 8
3.3 Protection .............................................. 10
4 INSTALLATION .......................................................... 11
4.1 Unpacking ............................................. 11
4.2 Location ................................................. 11
4.3 Batteries ................................................ 12
4.4 Connection examples ............................ 13
4.4.1 Models 1500W, 2000W, 3000W .......... 13
4.4.2 Models 3500W, 4500W, 5000W .......... 14
4.5 Wiring .................................................... 15
4.5.1 DC wiring ............................................ 15
4.5.2 AC wiring ............................................. 16
4.5.3 AC safety grounding ............................ 17
4.5.4 Network wiring (CZone/MasterBus) ..... 18
4.6 Tools and materials needed .................. 19
4.7 Installation step-by-step ......................... 20
4.8 Accessories connector (dry contacts) .... 23
4.8.1 Remote switch..................................... 24
4.8.2 Output ................................................. 24
5 SETTINGS .................................................................. 25
5.1 DIP switch settings ................................ 25
5.2 MasterBus configuration ........................ 26
5.2.1 Monitoring tab ..................................... 26
5.2.2 Alarms tab ........................................... 28
5.2.3 History tab ........................................... 28
5.2.4 Configuration tab ................................. 28
5.2.5 Events tab – System automation ......... 31
5.3 CZone configuration .............................. 32
6 OPERATION ............................................................... 34
6.1 Switching on / charge only .....................
34
6.2 Status LEDs ........................................... 34
6.3 Remote control ....................................... 35
6.4 3-step+ charge process.......................... 35
6.5 Temperature compensated charging ...... 36
6.6 Reset the thermal breaker after an
overload ................................................. 36
6.7 Maintenance .......................................... 37
6.7.1 Decommissioning ................................ 37
6.7.2 Storage and transportation .................. 37
7 PARALLEL AND SPLIT-PHASE SYSTEMS .............. 38
7.1 General information................................ 38
7.2 Materials needed ................................... 39
7.3 Preparations .......................................... 39
7.4 DC wiring ............................................... 40
7.5 AC wiring ............................................... 41
7.5.1 AC wiring of single-phase parallel
units ..................................................... 42
7.5.2 AC wiring of split-phase units (one unit
for each phase) .................................... 43
7.5.3 AC wiring of split-phase (two parallel
units for each phase) ........................... 45
7.6 Network wiring ....................................... 46
7.6.1 Preparation .......................................... 46
7.6.2 Network wiring of single-phase parallel
units ..................................................... 47
7.6.3 Network wiring of split-phase units ....... 47
7.6.4 Network wiring of two units in split-phase
with two units in parallel ....................... 48
7.7 Configuration and initial start-up ............. 48
7.7.1 DIP switches (for a single-phase parallel
configuration in a basic MasterBus
system) ................................................ 49
7.7.2 MasterAdjust ........................................ 50
7.7.3 CZone Configuration Tool .................... 51
7.8 Breaking down a cluster ......................... 53
8 TROUBLESHOOTING ................................................ 54
9 TECHNICAL DATA..................................................... 56
9.1 Inverter specifications ............................ 56
9.2 Charger specifications ............................ 57
9.3 Transfer system specifications ............... 59
9.4 Miscellaneous ........................................ 60
9.5 CZone specifications .............................. 60
9.6 Characteristics ....................................... 61
9.7 Dimensions ............................................ 62
To Next Page
Loading...
Need help?
General
