33
SVERKER 750/760
Programma Electric AB
ZP-CD01E R05A
5.8 Voltmeter
Voltmeter
<AC Volt Auto>
This option is used to make settings for the Sverker
voltmeter.
The voltmeter can be set to measure AC or DC. AC
readings are expressed as true RMS values while
DC readings are mean values.
Readings can be expressed in volts or percentages
of nominal voltage (which can be set from 1 to
999 V). These choices are called units on the menu.
IMPORTANT: To change a numerical value, you
press the CHG button one additional time and then
use the arrow buttons.
The range can be set to Auto or to Fixed low, Fixed
mid or Fixed high. The fixed ranges are useful for
short measurement cycles during which the voltme-
ter doesn’t have time to change range automatically.
If this occurs, O.F. (range overflow) is displayed
constantly.
For more information about the different ranges see
Chapter 9, Specifications.
noitpouneMevitanretlAnoitanalpxE
CA.1.tlACAserusaemretemtloV
SMReurtsa
CD.2.tlACDserusaemretemtloV
eulavnaemsa
t
nuhSm999-1 Ω roAsanwohssieulaV
Ak
tloV:tinU.1.tlAstlovninwohssiegatloV
fo%:tinU
Umon
.2.tlA%asanwohssiegatloV
ega
tlovlanimonehtfo
1morfegnarnachcihw
.V999ot
:UmoN
V360
—lanimonehttesotdesU
.egatlov
otuA:egnaR.1.tlAdetceleseg
naR
yllacitamotua
woL:egnaR.2.tlAegnarwoldexiF
diM:egnaR.3.tlAegnardimdexiF
hgiH:egnaR4.tlAegnarhgihdexiF
1. Press the SEL button to invoke the se-
lected option.
5.7 Ammeter
Ammeter
<AC Amp Auto>
This option is used to make settings for the Sverker
ammeter.
The ammeter can be set to measure AC or DC. AC
readings are expressed as true RMS values while
DC readings are mean values.
Readings can be expressed in amperes or percent-
ages of the nominal current (which can be set from 1
to 999 A). These choices are called units on the
menu. IMPORTANT: To change a numerical value,
you press the CHG button one additional time and
then use the arrow buttons.
The range can be set to Auto or to Fixed low or
Fixed high. The fixed ranges are useful for short
measurement cycles during which the ammeter
doesn’t have time to change range automatically. If
this occurs, O.F. (range overflow) is displayed
constantly.
For more information about the different ranges see
chapter 9, headed Specifications.
noitpouneMevitanretlAnoitanalpxE
CA1.tlACAserusaemretemmA
.SMReurtsa
CD2.tlACDserusaemretemmA
.eulavnaemsa
erepm
A:tinU.1.tlAninwohssitnerruC
.serepma
fo%:tinU
Imon
.2.tlAfo%sanwohssitnerruC
tnerruclanimoneht
1morfegnarnach
cihw
.A999ot
:ImoN
A100
—gnittestnerruclanimoN
otuA:egnaR.1.tlAdetcelesegnaR
yllacitamotua
woL:egnaR.2.tlAegnarwo
ldexiF
hgiH:egnaR.3.tlAegnarhgihdexiF
1. Press the SEL button to invoke the se-
lected option.
To Next Page
Loading...
