Merrychef conneX 12e - Technical Data Summary Sheet

6 Replacing components
Back to contents >
Merrychef conneX
®
service and repair manual
99
6.18 Technical Data Summary Sheet.
Fuse Ratings
Component Torque Settings (Nm)
Error Codes
F1 – F4
20A
USB Assembly
2.1
E81
Firmware updated
F5 – F6
13A (*12A)
Door Switches
1.0
E82
Menu updated
F7
3A
Door Skin
2.1
E83
Incompatible IO version
VFD Board
6.3A
Door Handle
2.1
E84
Date not set
Fuse Bracket
2.1
E86
Oven switched on
Overheat Thermostat settings
On/Off Switch PCB
1.0
E87
U/I held for 15 sec
Cavity Stat
300
o
C
Air Filter Assembly
1.0
E88
Supply voltage <180V
Mag Stat
125
o
C
Cavity to Base
2.1
E89
Recommission test failure cooling fan
Fan IP
160
o
C
Cooling Fan
2.1
E90
Recommission test failure convection fan
Door Choke
2.3
E92
Recommission test failure heater(s)
Current Draws @ 230VAC
Door Hinges
3.5
E93
Recommission test failure magnetron(s)
Magnetron
5.5 - 6
Mains Filter Bracket
2.1
E94
Recommission test failure air filter in
Cavity Overheat Thermostat
0.7
E95
Recommission test failure air filter out
Circuit Breaker Ratings
Panels
2.1
E96
Recommission test failure door switches close
conneX 12e
D16
Partition Plate
2.1
E97
Recommission test failure door switches open
Stirrers
1.0
E98
Incomplete cleaning cycle
Impinger Plate
1.2
E99
Filter override accepted
VFD Bracket
2.8
E100
Mains supply switched on
Component Resistances
Waveguides
2.1
E101
Magnetron failed on request.
EMI Filter L - N
330k
Heating Element Wiring
2.0
E102
Heater on without request.
Cooling Fan
220
Mains Filter Wiring
1.2
E103
Ambient Overheat. UI or IO >70
o
C
Stirrer Motor
7-8
Magnetron
2.1
E104
Safety circuit open (Overheat Thermostats)
Convection Fan
7.5 10%
Convection Fan Motor Assembly
2.1
E105
Supply frequency out of range by 2Hz
conneX 12e Heater
Element
19
Door Switch Bracket
2.8
E106
Cavity 75
o
C above setpoint or 300
o
C
UI to panel
0.8
E107
Communication fault between UI & IO
Magnetron
<1
IO Bracket
2.1
E108
Missing or corrupt UI Micro-SD
HV Transformer Pri
0.6*
HV Transformer to Base
3.5
E109
Missing or corrupt IO PM
HV Transformer Sec
570*
Voltage Selection Relay to Base
0.8
E110
Incompatible IO firmware
Capacitor
10M
Speaker
2.1
E111
Cavity sensor open circuit
Relay Coil
295
Cavity Thermocouple
1.7
E112
IO temperature sensor failure
LV Transformer
2.1
E113
Magnetron on without request. >1A
Steam Vent Pipe
2.1
E116
Heater off on request.
Maximum Cavity Temperature
Front Panel
2.1
E117
Mag Stat open circuit
260
o
C
Mains Filter to Bracket
2.8
Fuse Holder
1.0
VFD to Bracket
2.8
Cook Plate Studs
8.0
Heating Element
2.1
* see section 3.1 ‘Technical data, checks and verification’ for non-EU model specific readings where they differ.