Mitsubishi LE-40MTA-E - Setting Values and Data Selection; Various Setting Values

49
11.3 Various settng values
The items indicated with white letters on a black ground must be always set. Another items are set in ac-
cordance with the functinon used.
*1 : These parameter avail setting data copy by using memory cassette.
*2 : The setting of the item marked with "
× " on the " Setting during operation " column cannot be changed
while the MC input is turned on.
Set items Set values Unit
Set range
Initial
value
*1
Memory
cassette
transfer
*2
Setting
during
operation
Mainly
refer
page
M i n i m u m M a x i m u m
Ten sion
Tension
setting
Tension set value (N) N 0.1 ,1 or 10 ~ FS tension
–
NG c 18
Tension set value(×10N) N 0.01 ,0.1 or 1 ~ FS tension
–
NG c 18
Full scale
tension
Full scale value
–
1 1999 500
c
× 12
Decimal point (N)
–
0.1, 1.0 or 10 ×1 c × 12
Decimal point (×10N)
–
0.01 ,0.1 or 1 ×0.1 c × 12
Tension
detector
Zero adjustment
–
000NG× 12
Span adjustment
target value
N
1 digit ~ FS tension
(1/3 or more of FS tension)
500
c × 12
×10N 50.0
Filter
Display time constant s
1/4, 1/2, 1, 2,or 4
1/2 cc35
TMO output time constant s 1/2 cc42
Zero tension
detection
value
Zero tension (N) N 0 1999 0 c × 36
Zero tension (×10N) ×10N 0 199.9 0.0 c × 36
Manual setting Manual set value % 0 100
–
cc18
Tape r
Linear
taper
Taper ratio(int. diameter) % 0 80 0 cc31
Taper ratio(ext. diameter) % 0 100 0 cc32
Non-linear
taper
Corner 1~4 mmφ 0 2000 0 cc33
Taper 1~4 % 0 100 0 cc33
Start
Stall Stall set value % 0 100 20 cc15
Timer Start timer s 0.0 10.0 4.0 cc28
Output gain
Gain 1 % 5 400 100 cc29
Gain 2 % 5 400 100 cc29
New reel
/old reel
switch-over
New reel preset value % 0 100 50 cc25
Preset timer s 0.0 30.0 4.0 cc25
Old reel cut torque % 0 100 10 cc38
Stop control
Stop timer s 0.0 100.0 6.0 cc28
Stop gain % 5 400 100 cc28
Stop bias % 0 50 0 cc28
Mechanical loss
correction
Reel
A
Powder mode % 0 100 0 cc37
AC servo mode % –50 100 0 cc37
Reel
B
Powder mode % 0 100 0 cc37
AC servo mode % –50 100 0 cc37
Reel diameter
Minimum diameter mmφ 0 2000 100 c × 32
Maximum diameter mmφ
Minimum set
diameter
2000 1000 c × 32
Control gain
Manual
setting
Proportional gain (P gain) % 0 100 50 cc35
Integral time % 1 100 50 cc35
Dead zone gain % 0
100–P gain
0 cc35
Dead zone width % 0 100 50 cc35
Automatic
gain setting
Addition torque % 0 100 20 cc34
Password
–
0 32767 4095 × c 10