-21-
8.4. Limits
Menu Function Value Function Description
Ordinal Number in the "Parameters" Hot Menu
T cool.lim
Speed lim Speed Limit (km/h)
Fuel Lev Low Fuel Level Limit (l)
Hi batt.volt
The limit of the warning of the too low engine position (according to the trim sensor).
The limit of the warning of the too high engine position (according to the trim sensor).
№
Engine Temperature
Limit (°C)
30...150
>150
If the set limit is exceeded, the trip computer displays a warning message about engine
overheating and the value of the exceeded parameter.
T cylinder
lim
Cylinder Temperature
Limit (°C)
30...200
>150
If the set limit is exceeded, the trip computer displays a warning message about engine
overheating and the value of the exceeded parameter.
Only for the "Honda" protocol
Eng.speed
lim
Engine Speed Limit
(rpm)
2500...8000
>8000
If the set limit is exceeded, the trip computer displays a warning message about excessive
rpm and the value of the exceeded parameter.
40...200
>200
If the set limit is exceeded, the trip computer displays a warning message about excessive
speed and the value of the exceeded parameter.
5...99
>5
If the fuel level in the tank drops below the set limit, the trip computer displays a warning
message about low fuel level and the value of the parameter.
Low
batt.volt
Low Battery Voltage
Limit (V)
9...13,9
>10,5
If the voltage drops below the specified limit, the trip computer displays a warning message
about too low voltage (only when engine is on) and the value of the parameter. No warning at
the moment the ignition is being turned on.
High Battery Voltage
Limit (V)
14...16
>15,5
If the voltage exceeds the specified limit, the trip computer displays a message about too high
voltage and the value of the parameter.
Inj/
expense %
Limit of exceeded
injection duration and
instantaneous fuel
consumption per hour
at idle speed
(%)
1...99
>9
Sets the limit after which the trip computer warns about changes in fuel quality (when the "Fuel
Quality Control" function is turned on).
Positive change - shows percentage of increase in injection time and fuel consumption at idle
speed, the fuel is worse than the reference.
Negative change - displays percentage of decrease in injection time and fuel consumption at
idle speed, the fuel is better than the reference.
The mode may not work correctly when other electrical components are on.
Engine
heat.
Engine Heating Limit
(°С)
10...110
>70
When the engine temperature reaches the set limit, the trip computer issues a warning about
sufficient engine heating.
Consm.
100/h
Instantaneous
Consumption Switching
Limit
5...15
>10
Speed limit for switching the display of instantaneous fuel consumption from l/hour to l/100
km.
Arrows
Cns/100
Face Dimension When
Displaying
Instantaneous Fuel
Consumption
>24/80
24
80
Face dimension when displaying instantaneous fuel consumption per 100 km.
24/80 — from 0 to 24 at fuel consumption up to 24 l /100 km, from 0 to 80 at consumption
over 24 l/100 km
24 — from 0 to 24 at any value of instantaneous fuel consumption
80 — from 0 to 80 at any value of instantaneous fuel consumption
T eng.oil
lim
Engine Oil Temperature
Limit (°С)
30…150
>150
If the set limit is exceeded, the trip computer displays a message about the engine oil
overheating and the value of the exceeded parameter.
Only for "Honda, NMEA2000" protocols
Trim low
lim
Lowest Trim Position
Limit (deg)
-9...14
>5
Trim high
lim
Highest Trim Position
Limit
(deg)
6...90
>15
8.5. Time
Menu Function Value Function Description
Ordinal Number in the "Parameters" Hot Menu
Date Date Setting dd.mm.yy
Time Time Setting hh:mm
Time Date and Time Sourse
Time Zone Setting
Time Corr.
Alarm Alarm Setting hh:mm
Alarm Alarm Activation
№
Sets the current date in the format day:month:year. Press repeatedly the " SET" button to
select a group for editing:
«SET» - sets the date
«SET» - sets the month
«SET» - - «SET» sets the year and exits editing mode
Sets the current time in the format hours:minutes. Press repeatedly the " SET" button to select
a group for editing:
«SET» - sets the hour
«SET» -
«SET» sets minutes and exits editing mode
Man.
GPS
Man. - The on-board computer displays manaly set date and time.
GPS — Sets date and time received from the in-built GPS.
TimeZoneCor.
GPS
-12...+14
>3
Sets the time zone to display the correct time.
Only for Time - GPS
Time Correction
(sec.)
-30...30
0
Negative value - slows down the clock.
Positive value - speeds up the clock.
The adjustment happens once a day for a set number of seconds.
Sets the alarm time in the format hour :minute.
When the alarm goes off you will hear a sound signal and an "Alarm" message on the screen.
The alarm sounds for 1 minute or until any button is pressed. The alarm will go off only if the
"Alarm Act." parameter is set (see below).
Pass.
Act.
Pass. - the alarm is prohibited, the sound signal won't go off and the message will not be
displayed on the screen.
Act. - The alarm is allowed, the alarm will go off at the set time and will sound for 1 min. or
until any key is pressed.
To Next Page
Loading...