NARDA PMM 9010F - Page 4

IV Safety considerations
4 Sweep Mode operating instructions
4.1 Introduction………………………………………………………………………
4.2 Measure………………………………………………………………………….
4.2.1 Frequency……………………………………………………………………...
4.2.2 Level………………….………………………………………………………...
4.2.2.1 Input: Attenuator and Preamplifier….…………………………………….
4.2.2.2 Misc…………………………………………………………….…………….
4.2.2.2.1 Tracking generator……………………………………………………….
4.2.2.3 Detector……………………………………………………………………...
4.2.2.4 Smart detector…………………………………………………..................
4.2.3 Conversion factor……………………………………………………………..
4.3 Limit………………………………………………………………………………
4.4 Display……………………………………………………………………………
4.5 Marker…………………………………………………………………………….
4.6 Load & Store.…………………………………………………………………….
4.7 Ultra fast FFT scan……………………………………………………………...
Page
4-1
4-2
4-2
4-3
4-3
4-4
4-4
4-5
4-5
4-6
4-6
4-6
4-7
4-8
4-8
5 Analyzer Mode operating instructions
5.1 Introduction………………………………………………………………………
5.2 Frequency………………………………………………………………………..
5.3 RBW………………………………………………………………………………
5.4 Level………………………………………………………………………………
5.4.1 Input Attenuators and Preamplifier……..…………………………………..
5.4.2 OVER RANGE Message…………………………………………………….
5.4.3 Misc…………………..…………………………………………………………
5.4.3.1 Tracking generator…………………………………………………………
5.4.4 Detector………..……………………………………………………………….
5.4.5 Conversion factor……………………………………………………………..
5.5 Marker……..….………………………………………………………………….
5.6 Esc………………………………………………………………………………..
Page
5-1
5-2
5-3
5-3
5-3
5-4
5-4
5-5
5-5
5-6
5-6
5-6
6 Manual Mode operating instructions
6.1 Introduction………………………………………………………………………
6.2 Frequency………………………………………………………………………..
6.3 Level………………………………………………………………………………
6.3.1 Input: Attenuator and preamplifier………………………………………….
6.3.2 Misc…………………………………………………………………………….
6.4 RBW………………………………………………………………………………
6.5 Hold Time………………………………………………………………………...
6.6 Demodulator……………………………………………………………………..
Page
6-1
6-2
6-2
6-3
6-3
6-5
6-5
6-5
7. Applications
7.1 Measuring the EMI Voltage……………………………………………………...
7.1.1 Measuring Principle with a LISN………………………………………….....
7.1.2 Coupling Networks……………………………………………………………
7.1.2.1 AMN…………………………………………………………………………..
7.1.2.2 Current probe……………………………………………………………….
7.1.2.3 Voltage probe……………………………………………………………….
7.1.3 Test setup……………………………………………………………………..
7.1.4 Guidance on a preliminary Measuring Procedure………………………..
7.1.5 Remarks and hints for Measuring…………………………………………..
Page
7-1
7-1
7-1
7-2
7-3
7-3
7-4
7-4
7-5
8. Updating firmware and Activation code Utility
8.1 Introduction………………………………………………………………………
8.2 System requirements ……………………………….………………………….
8.3 Preparing the Hardware…………………………….………………………….
8.4 Software installation…………………………………………………................
8.5 To transfer data……………….……………………………………..………….
8.6 9010 Set code utility ...……….……………………………………..………….
Page
8-1
8-1
8-1
8-1
8-3
8-5