NARDA PMM 9010F - Page 5

EC Conformity V
9. PMM 9010/03P EMI CISPR Receiver
10 Hz ÷ 30 MHz Full compliance
> 30 MHz Compliance (PRF ≥ 10Hz)
PMM 9010/30P EMI CISPR Receiver
10 Hz ÷ 30 MHz Full compliance
30 MHz ÷ 3 GHz Pre compliance
PMM 9010/60P EMI CISPR Receiver
10 Hz ÷ 30 MHz Full compliance
30 MHz ÷ 6 GHz Pre compliance
General Information
9.1 Documentation…………………………………………………………………..
9.2 Operating Manual changes……………………………………………………
9.3 Introduction to PMM 9010/03P/30P/60P…...………………………………..
9.4 Instrument Items………….………………………………………………….....
9.5 Optional accessories……………….…………………………………………..
9.6 Other accessories………………………………………………………………
9.7 PMM 9010/03P Main Specifications…………………………………………..
9.8 PMM 9010/03P Front Panel……………..…………………………………….
9.9 PMM 9010/03P Rear Panel……………………………………………………
9.10 PMM 9010/30P Main Specifications…………..…………………………….
9.11 PMM 9010/30P Front Panel…………………….....………………...……….
9.12 PMM 9010/30P Rear Panel………………………..…………………………
9.13 PMM 9010/60P Main Specifications…………..…………………………….
9.14 PMM 9010/60P Front Panel…………………….....………………...……….
9.15 PMM 9010/60P Rear Panel………………………..…………………………
9-2
9-2
9-3
9-4
9-4
9-4
9-5
9-6
9-7
9-8
9-9
9-10
9-11
9-12
9-13
10 Click Mode Operating Instructions (Option)
10.1 Introduction……………………………………………………………………..
10.2 Click Mode Activation procedure…………………………………………….
10.3 Enter the Click Mode…………………………………………………….……
10.4 Introduction to the discontinuous disturbance (click) measurement….....
10.4.1 Determination of click rate………………………………………………….
10.4.2 Preliminary Conformity and Exceptions…………………………………..
10.4.2.1 Old and New exceptions…………………………………………………
10.4.3 Calculate Limit Quartile…………………………………………………….
10.4.4 Measurements vs Lq limit…………………………………………………..
10.5 Start………………………………………………………………………..……
10.5.1 Stop and pause…………………………………………………………..…
10.6 Report…………………………………………………………………………..
10.6.1 Fail during determination of the click rate N……………………………...
10.6.2 Report after a successful test with less than 5 instantaneous ………...
switching at one frequency…………………………………………..……..
10.6.3 Report after a successful test at 4 frequencies………………………….
10.6.4 Report after a line search…………………………………………………..
10.7 Setup…………………………………………………………….………………
10.7.1 External attenuator………………………………………………................
10.7.2 Limit…………………………………………………………………………...
10.7.3 Determination of N…………………………………………………………..
10.7.4 Factor f………………………………………………………………………..
10.7.5 Stop on Fail………………………………………………………................
10.7.6 Terminate on…………………………………………………………………
10.7.7 Line……………………………………………………………………………
10.7.8 Max time………………………………………………………………………
10.7.9 Idle Frequency.………………………………………………………………
10.7.10 Idle Level……………………………………………………………………
10.7.11 Smart Measure…………………………………………………………….
10.8 Click option…………………………………………………………………….
10.8.1 Optional PMM 9010 Click4E Four Channels Click meter ………………
10.9 Test setup………………………………………………………………………
10.10 Diagnostic…………………………………………………………………..…
10.11 Click reports with PMM Emission Suite ……………………………………
Page
10-1
10-1
10-4
10-5
10-6
10-6
10-6
10-7
10-7
10-7
10-9
10-9
10-9
10-9
10-10
10-10
10-11
10-11
10-12
10-13
10-13
10-13
10-14
10-14
10-16
10-16
10-16
10-16
10-17
10-17
10-18
10-18
10-19