Nibe VVM 310 - Item Register

Item register
A
Accessibility, electrical connection, 20
Accessories, 60
Alarm, 58
Assembly, 5
B
Back button, 33
C
Cable lock, 21
Commissioning and adjusting, 29
Commissioning without heat pump, 32
Connecting the circulation pumps, 30
Filling and venting, 29
Post-adjustment, venting, 32
Preparations, 29
Start guide, 31
Start-up and inspection, 31
Commissioning without heat pump, 32
Connecting accessories, 28
Connecting cold and hot water, 15, 18
Connecting current sensors, 26
Connecting EMK 310, 16
Connecting hot water circulation, 17
Connecting pool, 18
Connecting the circulation pumps, 30
Connecting the climate system, 15
Connecting to heat pump, 15
Connection as electric boiler, 15
Connection of external electrical addition, 16
Connection of external heat source, 16
Connections, 22
Contact for activation of “external adjustment", 27
Contact for activation of “temporary lux", 27
Contact information, 4
Control, 33, 37
Control - Introduction, 33
Control - Menus, 37
Control - Introduction, 33
Display unit, 33
Menu system, 34
Control knob, 33
Control - Menus, 37
Menu 1 - INDOOR CLIMATE, 37
Menu2-HOTWATER, 42
Menu 3 - INFO, 44
Menu4-MYSYSTEM, 45
Menu 5 - SERVICE, 50
D
Delivery and handling, 5
Assembly, 5
Installation area, 5
Removing the covers, 7
Supplied components, 6
Transport, 5
Dimensions and pipe connections, 12
Dimensions and setting-out coordinates, 61
Display, 33
Display unit, 33
Back button, 33
Control knob, 33
Display, 33
OK button, 33
Status lamp, 33
Switch, 33
Disturbances in comfort, 58
Alarm, 58
Manage alarm, 58
Troubleshooting, 58
Draining the climate system, 30, 55
Draining the hot water heater, 55
E
Electrical addition - maximum output, 24
Power steps of the immersion heater, 24
Electrical circuit diagram, 3 x 400 V, 65
Electrical connections, 19
Accessibility, electrical connection, 20
Cable lock, 21
Connecting accessories, 28
Connections, 22
Electrical addition - maximum output, 24
External connection options, 26
General, 19
Load monitor, 26
Miniature circuit-breaker, 19
Outdoor sensor, 22
Power connection, 22
Removing the cover, base board, 20
Removing the cover, immersion heater circuit board, 20
Removing the hatch, input circuit board, 20
Room sensor, 22
Settings, 24
Temperature limiter, 19
External connection options, 26
Contact for activation of “external adjustment", 27
Contact for activation of “temporary lux", 27
Possible selection for AUX inputs, 26
Possible selection for AUX output (potential free variable re-
lay), 27
Switch for external blocking of heating, 26
F
Filling and venting, 29
Draining the climate system, 30
Filling the climate system, 29
Filling the hot water coil, 29
Venting the climate system, 29
Filling the climate system, 29
Filling the hot water coil, 29
H
Help menu, 31, 36
Hot water capacity, 62
I
Important information, 2
Safety information, 2
Indoor module's design, 8
Component locations, 8
List of components, 9
Initial pressure, 10
Inspection of the installation, 3
Installation alternative, 13
Connecting cold and hot water, 15, 18
Connecting EMK 310, 16
Connecting hot water circulation, 17
Connecting pool, 18
Connecting the climate system, 15
Connecting to heat pump, 15
Connection as electric boiler, 15
Connection of external electrical addition, 16
Connection of external heat source, 16
Extra hot water heaters, 13
Two or more climate systems, 16
Water heater with immersion heater, 13
NIBE™ VVM 310Chapter 13 | Item register70
13 Item register