10 – English
English
TABLE 2
Parameters Value No. of ashes emitted by
the ashing light
Transmitter key to be
used
Actions to be performed
Pause time 10 sec 1 T1 Press T1 once
20 sec * 2 T1 Press T1 twice
40 sec 3 T1 Press T1 three times
60 sec 4 T1 Press T1 four times
Pedestrian
opening
Gate open to 0.7 m 1 T2 Press T2 once
Gate open to 1 m * 2 T2 Press T2 twice
Gate halfway open 3 T2 Press T2 three times
Gate 3/4 open 4 T2 Press T2 four times
Motor force Low 1 T3 Press T3 once
Medium-low * 2 T3 Press T3 twice
Medium-high 3 T3 Press T3 three times
High 4 T3 Press T3 four times
Step-by-Step
(SbS)
function
Open - Stop - Close - Stop 1 T4 Press T4 once
Open - Stop - Close - Open * 2 T4 Press T4 twice
Open - Close - Open - Close 3 T4 Press T4 three times
Opening only 4 T4 Press T4 four times
OGI (Open Gate
Indicator)
function
OGI 1 T5 Press T5 once
30 sec courtesy light 2 T5 Press T5 twice
60 sec courtesy light 3 T5 Press T5 three times
Presence function* (see Par. 9.1.2) 4 T5 Press T5 four times
* Factory value
9.1.2 - Presence function
This function is regulated by key T5 of the ECCO5... transmitter (Fig. in Table 4) and determines the operating mode of the OGI output. If LM100 lighting
modules (not supplied) are connected to this output, this function operates as follows:
- with the gate closed: when an opaque object interrupts transmission (infrared) of the photocells, the courtesy light switches on for 5 seconds. After
5 seconds, if the transmission is still interrupted, the courtesy light switches on for another 5 seconds; if instead the photocell does not detect any
object, the courtesy light switches off.
- with the gate moving (opening and closing manoeuvre): the courtesy light is always lit. At the end of the manoeuvre (opening or closing) it re-
mains lit for a further 5 seconds.
- with the gate open and automatic closing not active: at the end of the manoeuvre the courtesy light remains lit for 5 seconds then switches off
and follows the gate’s behaviour when closed.
- with the gate open and automatic closing active: at the end of the manoeuvre the courtesy light remains lit for 5 seconds then switches off and
follows the gate’s behaviour when closed.
If the OGI function is active, the lamp connected to it behaves in the following way:
- off: automation in fully closed position.
- slow flashing: execution of the opening manoeuvre.
- fast flashing: execution of the closing manoeuvre.
- steady lit: automation in fully open position.
9.1.3 - Verifying the values set for each parameter (using the transmitter memorised in mode 1)
The check can be effected by means of any transmitter memorised in Mode 1 (as those supplied, see Paragraph 9.3.1). If there is no transmitter memo-
rised in Mode 1, it is possible to memorise one solely for programming purposes then cancelling it (see Paragraph 9.4).
Adjustment procedure (before proceeding check the parameter to be verified in Table 3 and the action to be performed):
01. On the transmitter (Fig. 25) simultaneously press and hold buttons T1 and T2 for 5 seconds then release them.
02. Within 3 seconds from releasing them, perform the action specified in Table 3 to verify the desired parameter.
03. Release the key when the flashing light starts flashing: count the flashes. Check in Table 2 the value corresponding to the number of flashes.
TABLE 3
1
2
Parameters Actions to be performed
Pause time Press and hold key T1
Pedestrian opening Press and hold key T2
Motor force Press and hold key T3
SbS function Press and hold key T4
OGI function Press and hold key T5
9.2 - ADDING OR REMOVING DEVICES
It is possible to add or remove devices at any time to the system: if devices are added, it is important to
verify that these are perfectly compatible with FILO 400C/FILO 600C; for further details contact the Nice
technical support service.
9.2.1 - Memorising additional devices
The recognition operation of the devices connected to the ECSBus and to the Stop input is usually car-
ried out during the installation phase; but if devices are added (or removed) subsequently, the following
procedure must be carried out:
01. On the control unit press and hold button P2 (Fig. 26) for at least 3 seconds then release it.
25
Aerial
P4
L4 L3 L2
P3 P2
SbS
L1
P1
26
To Next Page
Loading...
