nord NORDAC PRO SK 511E Series - Page 149

5 Parameters
BU 0505 EN-3021 149
P543 [-01]
...
[-05]
Bus actual value
(Bus – Actual value)
S P
0 ... 57
{ [-01] = 1 }
{ [-02] = 4 }
{ [-03] = 9 }
{ [-04] = 0 }
{ [-05] = 0 }
In this parameter the return value for bus actuation can be selected.
NOTE:
The actual values 4 and 5 must be supported by the relevant bus module. For
further details please refer to the manual for the frequency inverter (P418, P543),
the relevant BUS operating instructions or the manuals BU 0510 / BU0550.
[-01] = Bus - Actual value 1 [-02] = Bus - Actual value 2 [-03] = Bus - Actual value 3
[-04] = Bus - Actual value 4 [-05] = Bus - Actual value 5
Pos: 355 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P500- P599/Parameter P543 - Bus- Istwerte, Einstel lungen [SK 5xxE] @ 2\mod_135426 7251544_388.doc x @ 51871 @ @ 1
0 =
Off
13 =
... 16 Reserved
1 =
Actual frequency
17 =
Value analog input 1
2 =
Actual speed
18 =
Value analog input 2
3 =
Current
19 =
Setpoint frequency master
value(P503)
4 =
Torque current (100% = P112)
20 =
Setpoint frequency master value after
ramp "Setpoint frequency master
value after ramp"
5 =
Digital IO status
4
21 =
Act. freq. without slip master value
"Actual frequency without slip master
value"
6 =
... 7 Reserved
22 =
Speed encoder  (only possible with
SK 520E and encoder feedback)
8 =
Setpoint frequency
23 =
Actual frequency with slip, "Actual
frequency with slip"
(SW V2.0 and above)
9 =
Error number
24 =
Master value, actual freq. with slip,
"Master value, actual freq. with slip"
(SW V2.0 and above)
10 =
... 11 Reserved
53 =
... 57 Reserved
12 =
BusIO Out Bits 0...7
Scaling details: (chapter 8.7)
Pos: 359 /Anleitungen/ Elektronik/F U und Starter/5. Parameter/ Parameterauflis tung (P000 ...)/P500- P599/Parameter P546 – Funk tion Bus-Sollwerte [ SK 54xE] @ 0\mod_1328098077630_38 8.docx @ 11939 @ @ 1
4
The assignment of the digital inputs in P543/ 544/ 545 = 5
Bit 0 = DigIn 1 Bit 1 = DigIn 2 Bit 2 = DigIn 3 Bit 3 = DigIn 4
Bit 4 = DigIn 5
Bit 5 = DigIn 6 (SK 520E and above) Bit 6 = DigIn 7 (SK 520E and above) Bit 7 = Dig. func. AIN1
Bit 8 = Dig. func. AIN1 AIN2
Bit 9 = DigIn 8 (SK 540E and above) Bit 10 = DigIn 1, 1.IOE (SK 540E and above) Bit 11 = DigIn 2, 1.IOE (SK 540E and above)
Bit 12 = Out 1/ MFR1
Bit 13 = Out 2/ MFR2 Bit 14 = Out 3/ DOUT1 (SK 520E and above) Bit 15 = Out 4/ DOUT2 (SK 520E and above)