To Next PageTo Next Page
Need help?Do you have a question about the Omron E5 J Series and is the answer not in the manual?
General| Model | E5J Series |
|---|---|
| Type | Temperature Controller |
| Ambient Operating Temperature | 0 to 55 °C |
| Input Type | Thermocouple, RTD |
| Output Type | Relay, Voltage, Current |
| Control Method | On/Off, PID |
| Power Supply | 100-240 VAC |
| Temperature Range | Depends on input type |
| Alarm Output | Yes |
| Mounting Method | Panel Mount |
| Protection Rating | IP20 |
Highlights features like fuzzy self-tuning, dual set point, IP54 protection, and serial communications.
Lists models like E5AJ, E5EJ, E5BJ with their standard and communication types.
Details Relay, Voltage, and Current Output Units required for specific models.
Lists communication boards (RS-232C, RS-422, RS-485) for specific models.
Details CT models, hole diameters, and their requirement for heater burnout alarm.
Lists available terminal cover models for different controller series.
Shows temperature ranges and selectable sensor inputs (thermocouple, resistance thermometer).
Details electrical and input/output specifications for the temperature controllers.
Lists indication accuracy, hysteresis, integral/derivative times, and control/sampling periods.
Covers insulation, dielectric strength, vibration, shock, life expectancy, and enclosure ratings.
Details electromagnetic compatibility (EMC) and safety certifications.
Specifies ratings for Relay, Voltage Output, and Linear Output Units.
Details specifications for the heater burnout alarm feature.
Lists ratings for current transformers used with the controllers.
Outlines communication protocols, transmission methods, baud rates, and codes.
Explains the function of displays (PV, SV) and indicators (Output, Alarm, HB) for the E5CJ model.
Explains the function of displays (PV, SV) and indicators (Output, Alarm, HB, Stop) for E5AJ/E5BJ/E5EJ models.
Details the internal switch configuration (Top/Bottom View) for the E5CJ model.
Details the internal switch configuration (Top/Bottom View) for E5AJ/E5BJ/E5EJ models.
Instructions for setting the temperature display unit to Fahrenheit.
Explains the function selector switch settings for various operations (Output, Control Mode, PID Tuning).
Describes how to select temperature sensor types and their corresponding ranges.
Details alarm modes, operations, outputs, and setting ranges based on switch position.
Explains how deviation and absolute alarm values are set relative to the set point.
Explains the key protection switch modes for write-protecting parameters.
Describes the two display levels for inputting and setting parameters.
Instructions for setting the primary (SP0) and secondary (SP1) set points.
Details how to set alarm 1 and alarm 2 values based on selected alarm modes.
Explains output value display, control period settings, and hysteresis adjustment.
Details how to set set points SP0 and SP1 using the Up/Down keys.
Explains how to display heater current and set the burnout alarm value.
Illustrates how to connect current transformers to the controller.
Provides wiring diagrams for E5CJ-H and E5EJ-H models, including alarm and CT connections.
Explains alarm mode selector settings and output retention reset procedures.
Details parameters for Proportional Band (P), Integral Time (I), and Derivative Time (d).
Covers Manual Reset, communication settings, stable range, and alarm hysteresis.
Explains setting temperature units, parity, data bit length, and stop bits.
Details PID control types (α) and automatic display return settings.
Describes event input selection and standby sequence reset methods.
Explains how to adjust alarm hysteresis and limit set point ranges.
Instructions for starting control operations and handling power-on sequences.
Lists common error messages, their causes, and troubleshooting steps.
Explains the self-tuning function, its modes, and startup conditions.
Details conditions for refreshing PID constants and achieving stable temperature status.
Describes HT startup conditions and procedures for starting/stopping auto-tuning.
Lists conditions that prevent or force-end auto-tuning and parameter changes during tuning.
Provides detailed physical dimensions for E5AJ, E5BJ, E5CJ, and E5EJ controller models.
Shows diagrams and dimensions for terminal cover models E53-COV02, E53-COV04, E53-COV03.
Illustrates E5AJ, E5CJ, and E5EJ controllers fitted with terminal covers.
Provides panel cutout dimensions for E5AJ, E5CJ, E5BJ, and E5EJ models.
Illustrates how to mount multiple controllers side-by-side.
Shows wiring connections for E5AJ and E5EJ models, including output and communication options.
Details wiring diagrams for E5BJ and E5CJ-2 B Standard Models.
Provides wiring diagrams for E5CJ-2 Simple Models and E5CJ Simple Models.
Covers guidelines for mounting, dismounting, and terminal connections.
Advises on input connections, lead wires, and sequenced circuits.
Lists ordering information, sizes, and materials for watertight covers.
Shows diagrams for watertight cover nomenclature, assembly, and dimensions.
Provides panel cutout details for specific watertight cover models.
Offers advice on opening/closing the cover and cleaning.
Illustrates connection examples between temperature controllers and SSRs.
Lists compatible SSR models and their specifications for connection.
