Omron FHV Series - Page 138

Omron FHV Series

164 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

6 Power Supply and I/O Interface

6 - 20

FHV Series Smart Camera Setup Manual (Z408-E1)

Table of Contents

Default Chapter3
- Intended Audience3
- Introduction3
- Applicable Products3
Relevant Manuals4
Manual Structure6
- Page Structure6
- Special Information7
- Table of Contents9
Sections in this Manual12
Terms and Conditions Agreement12
- Warranty, Limitations of Liability12
- Application Considerations13
- Disclaimers13
Safety Precautions15
- Symbols and the Meanings for Safety Precautions Described in this Manual15
- Meanings of Alert Symbols15
- Warning16
Precautions for Safe Use17
- Condition of the Fitness of OMRON Products17
- Installation Environment17
- Power Supply and Wiring17
- Mounting18
- Others19
Precautions for Correct Use20
- Installation Location20
- Power Supply, Connection, and Wiring20
- Maintenance21
- Beam21
- Image Sensor21
- Communications with Upper Equipment21
- Failsafe Measures22
- Warm-Up22
- Camera Installation22
- Others22
- LED Safety23
Regulations and Standards24
- Using Product Outside Japan24
- Conformance to KC Standards24
- Conformance to EC/EU Directives24
Related Manuals25
Terminology26
Revision History30
Smart Camera34
- FHV7H-□□□□□-C Series34
- FHV7H-□□□□□-S□□ Series34
Sold Separately36
- Cables36
- Modules37
- Accessories38
- Lighting and Lighting Controller40
- Software40
  - Overview of FHV Series41
Overview of System42
- Basic System of Measurement42
Flow of Use Procedure47
- Configuration49
Smart Camera50
- FHV Series50
Cables58
- I/O Cables58
- Ethernet Cables61
Lens Modules63
- Specifications63
- Meaning of Optical Chart65
C Mount Lenses68
- Specifications68
- Meaning of Optical Chart78
Lighting Modules85
- Specifications87
- Dimensions87
Optical Filters87
- Specifications89
Waterproof Hoods89
- Dimensions90
Mounting Fixtures94
- Specfications94
- Dimensions94
Software96
- Remote Operation Tool96
- Simulation Software96
  - Handling and Installation Environment97
Warning98
- Installation100
Assembling Equipment100
- C Mount Lens / IP40 Configuration100
- C Mount Lens / IP67 Configuration101
- Lens Module / IP40 Configuration103
- Lens Module / IP67 Configuration106
- Lens Module / Internal Lighting / IP67 Configuration108
Installing the Smart Camera112
- How to Connect112
- When Connecting the Smart Camera to a Lighting Controller116
When Turning Power on and off120
Fail-Safe Measures122
Precautions for I/O Interface123
I/O Cable Interface (Power Supply, I/O, RS-232C)124
- Recommended Power Supply for FHV Series124
- Cables125
- Pin Layout126
- Interface Specifications127
- I/O Interface Input / Output Circuit Diagram130
- RS-232C Interface132
Ethernet Interface133
- Cables134
- Pin Layout135
Inserting and Removing the Microsd Card136
- How to Insert / Remove the Microsd Card136
  - Software Setup139
Setting up the Software140
- Recommended Operational Environment140
- Installation140
- Windows141
- Use Procedures142
Operating the Smart Camera Remotely [Remote Operation Tool]148
- Environment Settings149
- Network Settings for the Remote Operation PC149
- Network Settings for the Smart Camera150
- Network Settings for the Smart Camera with Remote Operation Tool152
- Launching the Remote Operation152
- Terminating the Remote Operation155
Using the Simulation Software [Simulation Software]156
- Introduction156
- Available Image Formats156
- Operational Precautions156

Related product manuals

Preview: Omron fq2

Preview: Omron FQ2-S4

Omron FS-C2KU7DGES-C

Preview: Omron FS-C4KU7DGES-F

Omron FS-C4KU7DGES-F

Preview: Omron FQ2-S/CH Series

Omron FQ2-S/CH Series

Preview: Omron MicroHAWK F320-F

Omron MicroHAWK F320-F

Omron STC-HD213DV

Preview: Omron STC-MBS500POE

Omron STC-MBS500POE

Preview: Omron STC-MBS122BPOE

Omron STC-MBS122BPOE

Preview: Omron STC-HD213 Series

Omron STC-HD213 Series

Preview: Omron USB3 Vision Series

Omron USB3 Vision Series

Preview: CoaXPress STC-LBGP251BCXP124

CoaXPress STC-LBGP251BCXP124