What to do if Unit I/O Disconnection Detected for Channel 5 in Omron I/O Systems?
If a Unit I/O Disconnection is detected for Channel 5 in Omron I/O Systems, check the input wiring for breaks and replace the cable if necessary. Also, check the input wiring for bad connections and reconnect any that are found.
What to do if Unit I/O Disconnection Detected for Channel 4 in Omron NX-AD I/O Systems?
If a Unit I/O Disconnection is detected for Channel 4 in Omron I/O Systems, check the input wiring for breaks and replace the cable if necessary. Also, check the input wiring for bad connections and reconnect any that are found.
What to do if Unit I/O Disconnection Detected for Channel 3 in Omron I/O Systems?
If a Unit I/O Disconnection is detected for Channel 3 in Omron I/O Systems, check the input wiring for breaks and replace the cable if necessary. Also, check the input wiring for bad connections and reconnect any that are found.
What to do if Unit I/O Disconnection Detected for Channel 2 in Omron NX-AD?
If a Unit I/O Disconnection is detected for Channel 2 in Omron I/O Systems, check the input wiring for breaks and replace the cable if necessary. Also, check the input wiring for bad connections and reconnect any that are found.
What to do if Unit I/O Disconnection Detected for Channel 1 in Omron NX-AD?
If a Unit I/O Disconnection is detected for Channel 1 in Omron I/O Systems, check the input wiring for breaks and replace the cable if necessary. Also, check the input wiring for bad connections and reconnect any that are found.
What to do if Unit Calibration Value Parity Error occurs in Omron NX-AD?
To address a Unit Calibration Value Parity Error in Omron I/O Systems, cycle the power supply to the NX Unit. If the error persists, replace the NX Unit.
What to do if Analog Unit Calibration Parameter Error occurs in Omron NX-AD?
To resolve an Analog Unit Calibration Parameter Error in Omron I/O Systems, write the calibration values to the Analog Unit again.
How to fix NX Unit Clock Not Synchronized Error in Omron NX-AD I/O Systems?
To resolve an NX Unit Clock Not Synchronized Error in Omron I/O Systems, replace the specific NX Unit if the error occurs only in that unit. If the error occurs in all NX Units mounted on a CPU Unit, replace the CPU Unit.
What to do for Control Parameter Error in Master in Omron NX-AD?
If you are experiencing a Control Parameter Error in Master for Omron I/O Systems, download the Unit operation settings of the NX Unit again. If the error persists, replace the CPU Unit or Communications Coupler Unit, depending on which is applicable.
How to fix Non-volatile Memory Hardware Error in Omron I/O Systems?
To resolve a Non-volatile Memory Hardware Error in Omron I/O Systems, cycle the power supply to the Unit or restart the NX bus for CPU Units. For Communications Coupler Units, cycle the power supply to the Unit or restart the Slave Terminal. If the errors are detected in the Controller, reset all of the errors in the Controller.
General| Category | Analog Input Unit |
|---|---|
| Operating Temperature | 0 to 55 °C |
| Storage Temperature | -25 to 70 °C |
| Product Series | NX-AD |
| Isolation Method | Photocoupler isolation |
| Input Range | Voltage: 0 to 5V, 1 to 5V, 0 to 10V, -10 to 10V; Current: 0 to 20mA, 4 to 20mA |
| No. of inputs | 4 |
| Accuracy | ±0.1 % of F.S. |
| Input Type | Voltage/Current |
| Voltage Input Range | 0 to 5 V, 1 to 5 V, 0 to 10 V, -10 to +10 V |
| Current Input Range | 0 to 20 mA, 4 to 20 mA |
| Compatible Controller | NX Series CPU Units |
| Isolation | Between I/O terminal and internal circuit: Photocoupler isolation |
Manual title covering analog input and output units.
Explains notations like WARNING and Caution for safety.
General environmental and operational specifications for the units.
Detailed specifications specific to each analog I/O unit model.
Step-by-step guide for installing NX units.
Details on power supply options and connection methods.
Instructions for connecting wires to the terminal blocks.
Overview of different I/O refreshing methods available.
Details on specific functions like moving average and calibration.
Specific functions like load rejection and user calibration.
Methods for identifying and diagnosing unit errors.
Interpreting unit status indicators for error detection.
Troubleshooting using Sysmac Studio and other software.
Common and unit-specific troubleshooting solutions.
Detailed specifications for individual analog input and output units.
To Next Page
