EasyManuals Logo

Onkyo HT-S5400 User Manual

Onkyo HT-S5400
60 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #43 background imageLoading...
Page #43 background image
43
En
LipSync
` Off
` On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
You can change various audio settings from the Home
menu ( page 31).
Note
These settings are not available in either of the following cases:
a pair of headphones is connected.
–theAudio TV Out” setting is set to “On” ( page 42) and
an input selector other than HDMI is selected.
–“HDMI Ctrl (RIHD)” is set to On” ( page 42) and
you’re listening through your TV speakers.
Tone Control Settings
Bass
` –10 dB to 0dB
to +10 dB in 2 dB steps
You can boost or cut low-frequency sounds output
from the front speakers.
Treble
` –10 dB to 0dB
to +10 dB in 2 dB steps
You can boost or cut high-frequency sounds output
from the front speakers.
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
Operating on the AV receiver
Note
To bypass the bass and treble tone circuits, select the Direct
listening mode.
Speaker Levels
Subwoofer Level
*1
` –15 dB to 0dB to +12 dB in 1 dB steps
Center Level
` –12 dB to 0dB
to +12 dB in 1 dB steps
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to Standby. To save the setting you made
here, go to “Level Cal (Level Calibration)” ( page 37)
before setting the AV receiver to Standby.
Note
You cannot use this function while the AV receiver is muted.
Speakers that are set to “No” or “None” in the “Sp Config
(Speaker Configuration)” ( page 36) cannot be adjusted.
*1
This procedure can also be performed on the AV receiver by
using its SUBWOOFER LEVEL.
Audyssey
Audyssey
See “Audyssey” of “Source Setup” ( page 39).
Dynamic EQ
See “Dynamic EQ” of “Source Setup” ( page 39).
Dynamic Volume
See “Dynamic Volume” of “Source Setup” ( page 39).
Note
These technologies can be used when all the following
conditions are met:
Room Correction and Speaker Setup is completed. Note that
Audyssey” requires the “Audyssey 2EQ Full Calibration
method.
Any listening mode other than Direct is selected.
A pair of headphones is not connected.
The input selector other than USB is selected.
The setting is stored individually for each input selector.
After changing the settings of the “HDMI Ctrl
(RIHD)”, “HDMI Through” or “Audio Return Ch”,
turn off the power to all connected pieces of equipment
and then turn them on again. Refer to the instructions
for all connected pieces of equipment.
Using the Audio Settings
1
Press RECEIVER followed by HOME.
2
Use q/w and ENTER to select “Audio”, and then
use q/w/e/r to make the desired selection.
1
Press TONE on the AV receiver repeatedly to
select either “Bass” or “Treble”.
2
Use + and on the AV receiver to adjust.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Onkyo HT-S5400 and is the answer not in the manual?

Onkyo HT-S5400 Specifications

General IconGeneral
Disc types supportedNo
Optical disc player type-
Apple docking compatibilityiPhone, iPod
Audio decodersDolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio
RMS rated power- W
Audio output channels7.1 channels
Audio formats supportedAAC, FLAC, MP3, WMA
Signal-to-Noise Ratio (SNR)100 dB
Total Harmonic Distortion (THD)0.08 %
FM radioYes
AM band range530 - 1710 kHz
FM band range87.5 - 108 MHz
Supported radio bandsAM, FM
Preset stations quantity40
Front speaker type2-way
Front speaker impedance6 Ω
Front speaker peak power130 W
Front speaker frequency range55 - 50000 Hz
Satellite speaker frequency range80 - 20000 Hz
Subwoofer peak power120 W
Subwoofer frequency range25 - 150 Hz
Product colorBlack
HDMI in4
USB version2.0
Audio (L/R) in6
Composite video in5
SCART ports quantity0
Number of HDMI outputs1
Component video (YPbPr/YCbCr) in2
AC input voltage220-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)480 W
Package weight34000 g
Weight and Dimensions IconWeight and Dimensions
Main unit weight9000 g
Subwoofer weight10800 g
Center speaker weight2400 g
Satellite speaker weight1000 g
Main unit dimensions (WxDxH)435 x 328 x 150 mm
Subwoofer dimensions (WxDxH)317.5 x 398 x 463 mm
Front speaker dimensions (WxDxH)1550 x 170 x 375.5 mm
Center speaker dimensions (WxDxH)420 x 121 x 115 mm
Satellite speaker dimensions (WxDxH)115 x 96 x 230 mm

Related product manuals