Pace PAI - Page 10

PACE │ Installation & Assembly Manual
Issue Date: 07/03/2018
10
Form PA102.20-N1
LIST OF FIGURES (CONT'D)
FIGURE 94 - Installing Hepa Filter .......................................................................................................................... 58
FIGURE 93 - Visual Control Filter Clamps ..............................................................................................................58
FIGURE 95 - Installing Welded Bevel Seal Filter .................................................................................................... 59
FIGURE 96 - Supply Fan Restraint ......................................................................................................................... 60
FIGURE 97 - Thrust Restraint Assembly ................................................................................................................. 61
FIGURE 98 - Plenum Fan Thrust Restraint .............................................................................................................61
FIGURE 99 - Alignment Using Straight Edge .......................................................................................................... 63
FIGURE 100 - Alignment Using String .................................................................................................................... 63
FIGURE 101 - Sheave Angular Misalignment ......................................................................................................... 64
FIGURE 102 - Motor Base Lowered........................................................................................................................ 64
FIGURE 103 - Sheave Angular Alignment............................................................................................................... 64
FIGURE 104 - Sheave Angular Misalignment ......................................................................................................... 64
FIGURE 105 - V-Max Grid Lamps ........................................................................................................................... 65
FIGURE 106 - Installing V-Mod Lamp ..................................................................................................................... 65
FIGURE 107 - Installing V-Max Grid Lamps ............................................................................................................ 65
FIGURE 108 - UV Control Panel Wiring (8 amps)................................................................................................... 67
FIGURE 109 - UV Control Panel Wiring (Greater Than 8 Amps) ............................................................................ 68
FIGURE 110 - High and Low Connections for an in Fan Air Monitoring System ..................................................... 70
FIGURE 111 - High and Low Connections and Associated Tubing for Fan Mounted Air Monitoring System ......... 70
FIGURE 112 - Port Locations for Fan Mounted Air Monitoring System................................................................... 70
FIGURE 113 - Counterbalance Locked Into Place for Shipping .............................................................................. 71
FIGURE 114 - Counterbalance Unlocked for Start-Up ............................................................................................ 71
FIGURE 117 - Install Pipe Chase Base Rail to AHU Base Rail ............................................................................... 72
FIGURE 115 - Install Gasket Under Roof Overhang ............................................................................................... 72
FIGURE 116 - Apply Gasket to Pipe Chase ............................................................................................................ 72
FIGURE 118 - Install Flanges .................................................................................................................................. 72
FIGURE 119 - Apply Caulk to Base Rail.................................................................................................................. 73
FIGURE 120 - Apply Caulk Between Pipe Chase and AHU .................................................................................... 73
FIGURE 121 - Install Pipe Chase to Roof ............................................................................................................... 73
FIGURE 122 - Install Cover Angle ........................................................................................................................... 74
FIGURE 123 - Position Cover Angle Properly ......................................................................................................... 74
FIGURE 124 - Properly Install Screws .................................................................................................................... 74
FIGURE 125 - Apply Base Rail Cover ..................................................................................................................... 74
FIGURE 126 - Gas Furnace Fuel Venting System .................................................................................................. 75
FIGURE 127 - Gas Furnace Condensate Drain Trap .............................................................................................. 76
FIGURE 128 - Single Point Power Connection ....................................................................................................... 77
FIGURE 131 - Access Electrical Box....................................................................................................................... 78
FIGURE 129 - Typical Motor Data/Name Plate ....................................................................................................... 78
FIGURE 130 - Another Typical Motor Data/Name Plate .......................................................................................... 78
FIGURE 132 - Typical Power Wiring of Energy Recovery Wheel ........................................................................... 78
FIGURE 133 - Gas Burner Component Locations .................................................................................................. 79
FIGURE 134 - Main Power and Control Panel with Cover Open ............................................................................ 79
FIGURE 135 - Typical Electrical Heat Control Panel Interior Wiring and Components ........................................... 80
FIGURE 136 - Typical Field and Power Connections .............................................................................................. 80
FIGURE 137 - Pressure Probe Direction................................................................................................................. 82
FIGURE 138 - Air Flow Switch Connections ........................................................................................................... 82
FIGURE 139 - Layout of Typical Humidier Panel .................................................................................................. 84