Pace PAI - Page 9

Form PA102.20-N1
9
Installation & Assembly Manual │ PACE
Issue Date: 07/03/2018
LIST OF FIGURES (CONT'D)
FIGURE 48 - Assembling the End Channel Shipping Split with Energy Recovery Wheel ...................................... 40
FIGURE 49 - Installing the Direct Coupled Actuator................................................................................................ 41
FIGURE 50 - Installing MZ Damper......................................................................................................................... 42
FIGURE 51 - Damper Shaft Extension Kit (P/N 026-33715-002) ............................................................................ 43
FIGURE 52 - Second Tier Tie-Down Fastener Pack (P/N 386-03419-000) ............................................................ 43
FIGURE 53 - Bottom Raceway Shipping Split Fastener Pack (P/N 386-03418-000).............................................. 43
FIGURE 54 - Base Rail Shipping Split Fastener Pack (P/N 386-03417-000) ......................................................... 44
FIGURE 55 - Top Raceway Bracket Assembled (P/N 386-04747-000) ................................................................... 44
FIGURE 56 - Neoprene Gasket - 1/4 In. X 2 In. X 25 Ft (P/N 028-15954-010)....................................................... 44
FIGURE 57 - Neoprene Gray Gasket - 1/4 In X 3/4 In X 35 Ft (P/N 028-11873-010) for Door ............................... 44
FIGURE 58 - Phillips Hex Head Screw (P/N 021-32268-011) For Indoor Unit Seam Cap ...................................... 44
FIGURE 59 - Hex Head Screw For Outdoor Roof Seam Cap, Pipe Chase, and Rain Hood - 1/4 In-14 X 1 In (P/N
021-30530-052) ................................................................................................................................. 44
FIGURE 60 - Butyl Tape - 3/16 In X 3/4 In X 40 Ft (P/N 013E-03327-010) ............................................................. 44
FIGURE 61 - Polyurethane caulk (Grey: P/N 021-19568-000; Champagne: P/N 013-03317-040) For Pipe Chase
Only ................................................................................................................................................... 45
FIGURE 62 - Roof Seam Cap (Assembled) ............................................................................................................ 45
FIGURE 63 - Pipe Chase, Trim Angle, and Cover................................................................................................... 45
FIGURE 64 - Hood .................................................................................................................................................. 45
FIGURE 65 - Damper Shaft Extension Kit (P/N 026-33715-002) ............................................................................ 46
FIGURE 66 - Corner Connector Hole Plug (P/N 021-19568-000) (8) ..................................................................... 46
FIGURE 67 - Touch-Up Spray - 12 Oz. (P/N 013-03322-000) ................................................................................ 46
FIGURE 68 - Shipping Split Corner Gasket - 3.5 X 3. 5 (P/N 028-11883-010) ...................................................... 46
FIGURE 69 - Spare Fan Belt ................................................................................................................................... 46
FIGURE 70 - Conduit (P/N 025-39024-001) and SJO Cord (P/N 025-35746-001) ................................................. 46
FIGURE 71 - Typical Filter Types ............................................................................................................................ 47
FIGURE 72 - Filter Latches ..................................................................................................................................... 48
FIGURE 73 - Correctly Installed Latch Pin (P/N 026-35788-702) ........................................................................... 50
FIGURE 74 - Fully Installed Filter ............................................................................................................................ 51
FIGURE 75 - Correctly Installed Latch Pin (P/N 026-35788-604) ........................................................................... 51
FIGURE 76 - Place End of Latch Over Filter Frame ............................................................................................... 51
FIGURE 77 - Correctly Installed Cartridge Filter ..................................................................................................... 52
FIGURE 78 - Correctly Installed Latch Pin (P/N 026-35788-604) ........................................................................... 52
FIGURE 79 - Correctly Installed Cartridge with Pleats ............................................................................................ 52
FIGURE 80 - Correct use of Knockouts .................................................................................................................. 53
FIGURE 81 - Correct Latchout/Knockout Conguration .......................................................................................... 53
FIGURE 82 - Frame with Four Latches Installed on the Sides................................................................................ 53
FIGURE 83 - Spring Latch Pulled and Fastened in Filter Hole ............................................................................... 53
FIGURE 84 - Correct Latchout/Knockout Conguration (P/N 026-35788-612) ....................................................... 54
FIGURE 85 - Spring Latch Pulled and Fastened in Filter Hole ............................................................................... 54
FIGURE 86 - Installing Pre-Filter Latch ................................................................................................................... 54
FIGURE 87 - Position Pre-Filter in Front of Final Filter ........................................................................................... 55
FIGURE 88 - Spring End of Latch ........................................................................................................................... 55
FIGURE 89 - Completed Assembly ......................................................................................................................... 55
FIGURE 90 - Installation of Koch HEPA Filters ....................................................................................................... 56
FIGURE 91 - Koch HF ............................................................................................................................................. 57
FIGURE 92 - Hepa Filter (Cross Section) ............................................................................................................... 57