Panasonic SA-PM45PC - IC7002 and IC803 Terminal Functions

Pin No. Mark I/O Function
1 IN2 I Motor Driver Input
2 PC2 I Turntable Motor Drive Signal
(“L”:ON)
3 IN1 I Motor Drive (1) Input
4 PC1 - Traverse Motor Drive Signal
(“L”): ON)
5-8 N.C. - No Connection
9 PGND1 - Ground Connection (1) for Drive
10 PVCC1 - Power Supply (1) for Drive
11 D1- O Motor Drive (1) reverse - action
output
12 D1+ O Motor Drive (1) forward - action
output
13 D2- O Motor Drive (2) reverse - action
output
14 D2+ O Motor Drive (2) forward - action
output
Pin No. Mark I/O Function
1 PCONT1 O Power Control Output 1(Pwr
Sply,Active HIGH)
2 PCONT2 O Power Control Output 2
3 N.C. - No Connection
4 FL_DATA /
OCD_SDA
O FL Data Output / On Chip
Debugger Data
5 USB_RST O USB Reset Pin
6 FL_CLK /
OCD_SCL
O FL CLK Output / On Chip
Debugger Clock
7 USB_REQ I USB Interrupt Request
8 N.C. - No Connection
9 N.C. - No Connection
10 N.C. - No Connection
11 MMOD (GND) - Memory mode selection
(Ground connection)
12 OSC2 (8MHz) O Main Oscillator output (8MHz)
13 OSC1 (8MHz) I Main Oscillator input (8MHz)
14 VSS - Micom GND
15 XI (32kHz) I Slow Oscillator input (32KHz)
16 XO (32KHz) O Slow Oscillator output (32KHz)
17 VDD3.3 - Voltage supply 3.3V
18 VDD1.8 - Connect to pin 37
19 NRST I MICOM RESET PIN (L: reset)
20 N.C. - No Connection
21 MMOD0 O Switching Mode
22 TERR I Time out error
23 VERR O Verify error
24 DAB_PCONT - No Connection
25 RMT I Remote Control Input
26 HALT I AC Failure Detect Signal
27 DAB_
DDOWFIC
- No Connection
28 DAB_IRQ - No Connection
29 BLKCK I CD Subcode Block Clock Input
30 N.C. - No Connection
31 CD_MDATA O CD LSI Command Data
32 STAT I CD LSI Status Input
33 CD_MCLK O CD LSI Command Clock
34 USB_SDA I/O USB I2C Data Line
35 CD_MLD O CD LSI Command Load
36 USB_SCL I USB I2C Clock Line
37 VDD18 - Power Supply (1.8V)
38 MUTEA O Analog MUTE Output(L:M UTE
ON)
39 VSS - Micom GND
Pin No. Mark I/O Function
15 D3- O Motor Drive (3) reverse - action
output
16 D3+ O Motor Drive (3) forward - action
output
17 D4- O Motor Drive (4) reverse - action
output
18 D4+ O Motor Drive (4) forward - action
output
19 PVCC2 - Power Supply (2) for Driver
20 PGND2 - Ground Connection (2) for Driver
21-24 N.C. - No Connection
25 VCC I Power Supply terminal
26 VREF I Reference Voltage Input
27 IN4 I Motor Driver (4) Input
28 IN3 I Motor Driver (3) Input
Pin No. Mark I/O Function
40 ASP_CLK O ASP Sound Processor Serial
Clock Output
41 ASP_DATA O ASP Sound Processor Serial
Data Output
42 N.C. - No Connection
43 N.C. - No Connection
44 N.C. - No Connection
45 CD_RST O CD LSI Reset Ouput (L: reset)
46 N.C. - No Connection
47 DEMO_SET I Demo Mode Setting Input
48 MODEL_S EL I D-Port Select (H: D-Port, L:
Deck)
49 TU_STEREO I/O Tuner Stereo Signal
50 TU_SDA I/O IIC Serial Data for Tuner (PLL
Data I/O)
51 TU_CLK O IIC Serial Clock for Tuner (PLL
Clock Output)
52 VOL_JOG1 I Jog Input 1
53 VOL_JOG2 I Jog Input 2
54 TU_TUNED I/O Tuner Tuned Signal
55 N.C. - No Connection
56 N.C. - No Connection
57 N.C. - No Connection
58 N.C. - No Connection
59 N.C. - No Connection
60 N.C. - No Connection
61 N.C. - No Connection
62 CRTIMER I/O CR TIMER
63 VSS - Micom GND
64 FL_STROBE O Chip select for FL Panel
65 CLOSE_L O CD Tray Close Control (Active
L)
66 OPEN_H O CD Tray Open Control (Active
H)
67 DAB_RST - No Connection
68 DAB_ TU_RST - No Connection
69 DAB_ TU_SCL - No Connection
70 DAB_ TU_SDA - No Connection
71 N.C. - No Connection
72 DAB_RX - No Connection
73 RDS_DATA I RDS Data Input
74 RDS_CLK I RDS Clock Input
75 DAB_MODE - No Connection
76 UART_IN - No Connection
77 UART_OUT - No Connection
18.2. IC7002 (BA5948FPE2) IC 4CH Drive
18.3. IC803 (MN101EF16ZXW) MICROPROCESSOR
65
SA-PM45PC