Panasonic WV-SP302 - Table of Contents

30
 • When"FTPerror"isselectedfor"Savetrigger",the
file name entered for "File name" on the [FTP img.
trans.] tab of the "Network" page will be used for
the file name of the image saved on the SD memory
card.
[Image saving interval/Number of images to be
saved - Image saving interval]]
When "Alarm input" or "Manual" is selected for "Save
trigger", select an interval (frame rate) of saving images
on the SD memory card from the following.
0.1fps/0.2fps/0.33fps/0.5fps/1fps
Default: 1fps
[Image saving interval/Number of images to be
saved - Number of images to be saved]
Select a number of alarm images to be saved on the SD
memory card from the following.
10pics/20pics/30pics/50pics/100pics/200pics/300pics/
500pics/1000pics/2000pics/3000pics
Default: 100pics
Note:
 • When "H.264" is selected for "Recording format",
Pre alarm and Post alarm can be set on "H.264
recording" of [Alarm] tab.
 • "Numberofimagestobesaved"canbeconfigured
only when "Alarm input" is selected for "Save trig-
ger".
[Image capture size]
When "Manual" is selected for "Save trigger" and "JPEG"
is selected for "Recording format", select the image cap-
ture size of the images to be saved on the SD memory
card from the following.
When "4:3" is selected for "Aspect ratio"
QVGA/VGA/1280x960*1
QVGA/VGA/800x600*2
When "16:9" is selected for "Aspect ratio"
320x180/640x360/1280x720*1
320x180/640x360*2
Default: VGA
Note:
 • When"FTPerror"isselectedfor"Savetrigger",images
will be saved with the image capture size selected on
the [FTP img. trans.] tab of the "Network" page.
 • When"H.264"isselectedfor"Recordingformat",
select the image capture size for "H.264 recording" -
"Image capture size" on the [SD memory card] tab.
 • When "Alarm input" is selected for "Save trigger",
images will be saved with the image capture size
selected on the [Alarm] tab of the "Alarm" page.
■ H.264 recording
This setting is available only when "H.264" is selected for
"Recording format" of the SD memory card.
When the second [Set] button on the setup page is
clicked, the settings for "H.264 recording" will be dis-
played on the bottom of the tab.
[Image capture size]
Select the image capture size from the following.
When "4:3" is selected for "Aspect ratio"
QVGA/VGA *1
QVGA/VGA *2
When "16:9" is selected for "Aspect ratio"
320x180/640x360*1
320x180/640x360*2
Default: VGA
[Recording priority]
Select "Constant bit rate" or "Frame rate" for the H.264
recording mode.
Constant bit rate: H.264 images will be recorded with
the bit rate selected for "Constant bit rate".
Frame rate: H.264 images will be recorded with the
frame rate selected for "Frame rate*".
Default: Constant bit rate
[Frame rate*]
Select the frame rate for images to be recorded from the
following.
1fps/3fps/5fps */7.5fps */10fps */12fps (PAL models)/
15fps */20fps */30fps *
Default: "30fps*"
Note:
 • When"Framerate" is selected for "Recording priority",
this setting is available.
 • "Framerate*" is synchronized with "Constant bit rate".
For this reason, the frame rate may be lower than the
specified value when any value marked with an asterisk
(*) is selected.
*1
SP306
SP305
SF336
SF335
*2
SP302
SF332