Panasonic WV-SP302 - [Recording Priority]; Default: VGA; Default: Constant Bit Rate; [Frame Rate*]

47
Note:
 • When"On"isselected,only"Unicastport(AUTO)"
will be available for "Transmission type".
 • When"On"isselected,itmaytakesecondstostart
displaying MPEG-4 images.
 • When"On"isselected,MPEG-4imagesmaynotbe
displayed depending on the number of the concur-
rent access users and audio data availability, etc.
 • When"On"isselected,onlyIPv4accessisavail-
able.
 • When"On"isselectedforeither"MPEG-4(1)"or
"MPEG-4(2)",themaximumconcurrentaccess
number is equal to or less than 10 users.
[Image capture size]
Select "QVGA" or "VGA" for the image capture size of
MPEG-4 images.
Default: MPEG-4(1): VGA
MPEG-4(2): VGA
[Transmission priority]
Select "Constant bit rate" or "Frame rate" for the
MPEG-4 transmission mode.
Constant bit rate: MPEG-4 images will be transmitted
withthebitrateselectedfor"Maxbitrate(percli-
ent) *".
Frame rate: MPEG-4 images will be transmitted with
the frame rate selected for "Frame rate*".
Default: Constant bit rate
Note:
When "Frame rate" is set for "Transmission priority",
number of users who can access the camera may
be limited more (may become less than 10).
[Frame rate*]
Select a frame rate for MPEG-4 images from the follow-
ing.
1fps/3fps/5fps */7.5fps */10fps */12fps (PAL models) */
15fps */20fps */30fps *
Default: 30fps *
Note:
 • When"Framerate"isselectedfor"Transmission
priority", this setting is available.
 • "Framerate*"issynchronizedwith"Maxbitrate
(per client)*". For this reason, the frame rate may be
lower than the specified value when any value
marked with an asterisk (*) is selected.
[Max bit rate (per client) *]
Select a MPEG-4 bit rate per a client from the following.
64kbps/128kbps */256kbps */384kbps */512kbps */
768kbps */1024kbps */1536kbps */2048kbps */
3072kbps */4096kbps */Unlimited **
Default: MPEG-4(1): 2048kbps *
MPEG-4(2): 2048kbps *
* "Unlimited **" is available only when "Frame rate" is
selected for "Transmission priority".
Note:
 • TheMPEG-4bitrateissynchronizedwith
"Bandwidth control(bit rate)" on the [Network] tab of
"Network" page (☞ page 79). For this reason, the bit
rate may be lower than the value when any value
with an asterisk (*) on the right is selected.
 • When"Unlimited*"isselected,thenumberofusers
who can access MPEG-4 images will be limited to
"1".(OnlyasingleusercanaccessMPEG-4imag-
es.)
 • Itisimpossibletoselect"Unlimited*"forboth
"MPEG-4(1)" and "MPEG-4(2)".
[Image quality]
Select the image quality of MPEG-4 images from the
following.
Fine(Image quality priority)/Normal/Low(Motion priority)
Default: Normal
Note:
 • When"Constantbitrate"isselectedfor
"Transmission priority", this setting is available.
[Refresh interval]
Select an interval (I-frame interval; 0.2 - 5 seconds) to
refresh the displayed MPEG-4 images.
If using under a network environment with frequent
error occurrences, shorten the refresh interval for
MPEG-4 to diminish image distortions. However, the
refresh interval may be longer than the set value.
0.2s/0.33s/0.5s/1s/2s/3s/4s/5s
Default: 3s
[Transmission type]
Select the transmission type of MPEG-4 images from
the following.
Unicast port (AUTO): Up to 14 users can access a sin-
gle camera concurrently. "Unicast port1(Image)" and
"Unicast port2 (Audio)" will automatically be select-
ed when transmitting images and audio from the
camera.