Panasonic WV-SP302

43
[Internet mode (over HTTP)]
Select"On"whentransmittingH.264imagesviathe
Internet. It is possible to transmit H.264 images without
changing the broadband router settings configured for
JPEG image transmission.
On: H.264 images and audio will be transmitted using
the HTTP port. Refer to page 79 for further informa-
tion about the HTTP port number settings.
Off: H.264 images and audio will be transmitted using
the UDP port.
Default:Off
Note:
 • When"On"isselected,only"Unicastport(AUTO)"
will be available for "Transmission type".
 • When"On"isselected,itmaytaketimetostartdis-
playing H.264 images.
 • When"On"isselected,H.264imagesmaynotbe
displayed depending on the number of the concur-
rent access user and audio data availability, etc.
 • When"On"isselected,onlyIPv4accessisavail-
able.
• When"On"isselectedforeither"H.264(1)"or
"H.264(2)",themaximumconcurrentaccessnum-
ber is equal to or less than 10 users.
[Image capture size]
Select the image capture size from the following.
When "4:3" is selected for "Aspect ratio"
H.264(1) QVGA/VGA/1280x960*1
QVGA/VGA/800x600*2
H.264(2) QVGA/VGA
When "16:9" is selected for "Aspect ratio"
H.264(1) 320x180/640x360/1280x720*1
   320x180/640x360*2
H.264(2) 320x180/640x360
Default: H.264(1) 1280x960*1
VGA *2
H.264(2) VGA
[Transmission priority]
Select "Constant bit rate" or "Frame rate" for the H.264
transmission mode.
Constant bit rate: H.264 images will be transmitted
withthebitrateselectedfor"Maxbitrate(percli-
ent) *".
Frame rate: H.264 images will be transmitted with the
frame rate selected for "Frame rate*".
Default: Constant bit rate
Note:
 • When"Framerate"issetfor"Transmissionpriority",
number of users who can access the camera may
be limited more (may become less than 10).
[Frame rate*]
Select a frame rate for H.264 images from the following.
1fps/3fps/5fps */7.5fps */10fps */12fps (PAL models) */
15fps */20fps */30fps *
Default: 30fps *
Note:
 • When"Framerate"isselectedfor"Transmission
priority", this setting is available.
 • "Framerate*"issynchronizedwith"Maxbitrate
(per client)*". For this reason, the frame rate may be
lower than the specified value when any value
marked with an asterisk (*) is selected.
[Max bit rate (per client) *]
Select a H.264 bit rate per a client from the following.
64kbps/128kbps */256kbps */384kbps */512kbps */
768kbps */1024kbps */1536kbps */2048kbps */
3072kbps */4096kbps */8192kbps */Unlimited *
Default: H.264(1): 4096kbps *
H.264(2): 1536kbps *
* "8192kbps" is available only when the image cap-
turesizeis"1280x960",1280x720,or800x600.
* "64kbps" and "128kbps" are available only when
the image capture size is "QVGA", "VGA",320x
180,or640x360.
* "Unlimited *" is available only when "Frame rate" is
selected for "Transmission priority".
Note:
 • TheH.264bitrateissynchronizedwith"Bandwidth
control(bit rate)" on the [Network] tab of "Network"
page (☞ page 79). For this reason, the bit rate may
be lower than the value when any value with an
asterisk (*) on the right is selected.
 • When"8192kbps*"or"Unlimited*"isselected,the
number of users who can access H.264 images will
belimitedto"1".(Onlyasingleusercanaccess
H.264 images.)
 • Itisimpossibletoselect"Unlimited*"forboth
"H.264(1)" and "H.264(2)".
*1
SP306
SP305
SF336
SF335
*2
SP302
SF332