Pioneer PDP-507XD - Plasma Television protection function; Information of pixel defect; Infrared rays; Radio interference

PDP-507XD
9
5678
56
7
8
C
D
F
A
B
E
5.3.1 BLOCK DIAGRAM OF THE SHUT-DOWN SIGNAL ........................................................................104
5.3.2 SHUT DOWN OF FAILURE ANALYSIS ...........................................................................................105
5.4 NON-FAILURE SYMPTOMS ..................................................................................................................106
6. DISASSEMBLY .............................................................................................................................................107
6.1 PCB LOCATION .....................................................................................................................................107
6.2 FLOWCHART OF THE MAIN PARTS AND PC BOARDS EXCHANGE.................................................108
7. ADJUSTMENT ..............................................................................................................................................113
7.1 PARTS CHANGE OF NOTES.................................................................................................................113
7.2 ADJUSTMENT REQUIRED WHEN THE SET IS REPAIRED OR REPLACED......................................113
7.3 ADJUSTMENT REQUIRED WHEN PART IS REPLACED .....................................................................114
7.4 BACKUP WHEN THE PANEL UNIT IS ADJUSTED...............................................................................115
7.5 ADJUSTMENTS WHEN THE SERVICE PANEL ASSY IS REPLACED.................................................118
7.6 ADJUSTMENTS WHEN THE DRIVE ASSYS ARE REPLACED............................................................125
7.7 HOW TO CLEAR HISTORY DATA ..........................................................................................................128
8. SERVICE FACTORY MODE .........................................................................................................................129
8.1 OUTLINE OF THE SERVICE FACTORY ................................................................................................129
8.1.1 SERVICE FACTORY MODE TRANSITION CHART.........................................................................129
8.1.2 HOW TO ENTER/EXIT SERVICE FACTORY MODE.......................................................................129
8.1.3 OPERATION OF SERVICE FACTORY MODE.................................................................................130
8.1.4 REMOTE CONTROL CODE ............................................................................................................131
8.1.5 FACTORY HIERARCHICAL TABLE .................................................................................................132
8.1.6 INDICATIONS IN SERVICE FACTORY MODE ................................................................................133
8.2 FACTORY MENU....................................................................................................................................135
8.2.1 INFORMATION.................................................................................................................................135
8.2.2 PANEL FACTORY MODE.................................................................................................................143
8.2.3 OPTION............................................................................................................................................153
8.2.4 INITIALIZE........................................................................................................................................153
9. LIST OF RS-232C COMMANDS ..................................................................................................................156
9.1 OUTLINE OF RS-232C COMMANDS....................................................................................................156
9.1.1 PREPARED TOOLS .........................................................................................................................156
9.1.2 USING RS-232C COMMANDS........................................................................................................156
9.1.3 COMMAND PROTOCOL..................................................................................................................157
9.1.4 DEFINITION OF COMMAND...........................................................................................................158
9.2 LIST OF RS-232C COMMANDS............................................................................................................160
9.3 OUTLINE OF COMMANDS....................................................................................................................166
9.3.1 QS1 ..................................................................................................................................................166
9.3.2 QS2 ..................................................................................................................................................167
9.3.3 QIP ...................................................................................................................................................168
9.3.4 QAJ ..................................................................................................................................................168
9.3.5 QPW.................................................................................................................................................169
9.3.6 QPM .................................................................................................................................................169
9.3.7 QPD..................................................................................................................................................170
9.3.8 QSD..................................................................................................................................................171
9.3.9 QS6 ..................................................................................................................................................172
9.3.10 QMT ...............................................................................................................................................172
9.3.11 QNG ...............................................................................................................................................173
9.3.12 DRV................................................................................................................................................174
9.3.13 OTHER COMMANDS ....................................................................................................................175
10. GENERAL INFORMATION .........................................................................................................................176
10.1 POWER ON SEQUENCE.....................................................................................................................176
10.2 POWER SUPPLY TRANSITION STATUS.............................................................................................177
10.3 POWER ON/OFF FUNCTION FOR THE LARGE-SIGNAL SYSTEM ..................................................180
10.4 LED INFORMATION.............................................................................................................................181
10.5 SPECIFICATION ABOUT THE THERMAL PROTECTION...................................................................182
10.6 PROCESSING IN ABNORMALITY ......................................................................................................183
11. SPECIFICATIONS.......................................................................................................................................185
11.1 MAIN SPECIFICATIONS ......................................................................................................................185
11.2 ACCESSORIES....................................................................................................................................186
11.3 PANEL FACILITIES...............................................................................................................................187
12. IC INFORMATION .......................................................................................................................................189