powersoft K10 DSP+AESOP User Manual

▶
6
K Series User Guide
emissions FCC standard section 15.109, IEC CISPR standard Pub.
22 ed 6.0 (2008-09) CLASS A chapter 7.1.1, Conducted emission
FCC standard section 15.107, IEC CISPR standard Pub. 22 ed 6.0
(2008-09) CLASS B.
This equipment has been tested and found to comply by Notied
Body 2047(Directive 2006/95/EC L.V.) pursuant to the audio
apparatus safety requirements: Standard EN 60065
In a domestic environment this product may cause radio
interferences in which case the user may be required to take
adequate measures.
Average half-cycle r.m.s. inrush current on initial switch-on
K2, K2DSP, K3, K3DSP: 10 A
K6, K6DSP, K8, K8DSP, K10, K10DSP: 50 A
K20, K20DSP: 50 A
Average half-cycle r.m.s. inrush current after a supply
interruption of 5s.
K2, K2DSP, K3, K3DSP: 10 A
K6, K6DSP, K8, K8DSP, K10, K10DSP: 10 A
K20, K20DSP: 10 A
1.3 Warning Notices
Note: This equipment has been tested and found to comply
with the limits for Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
Information to User
Alterations or modications carried out without appropriate
authorization may invalidate the user’s right to operate the
equipment.
1.3.1 Location
Install the amplier in a well-ventilated location where it will not
be exposed to high temperature or humidity. Do not install the
amplier in a location that is exposed to direct sun rays, or near
hot appliances or radiators. Excessive heat can adversely affect the
cabinet and internal components. Installation of the amplier in a
damp or dusty environment may result in malfunction or accident.
1.3.2 Precautions Regarding Installation
Placing and using the amplier for long periods of time on heat
generating sources will affect its performance. Avoid placing the
amplier on heat generating sources. Install this amplier as far as
possible from tuners and TV sets. An amplier installed in close
proximity of such equipment may experience noise or generic
performance degradation.
WARNING: To prevent re or electric shock:
▶
The ventilation openings must not be impeded by any item
such as newspapers, tablecloths, curtains etc; keep a distance
of at least 50 cm from the front and rear ventilation openings
of the amplier.
▶
Do not expose this amplier to rain or moisture.
▶
This equipment must not be exposed to dripping or splashing
liquids: objects lled with liquids, such as vases, must not be
placed on the amplier.
1.4 Safety Rules
▶
This device must be powered exclusively by earth connected
mains sockets in electrical networks compliant to the IEC 364
or similar rules.
▶
It is absolutely necessary to verify this fundamental
requirement of safety and, in case of doubt, require an
accurate check by qualied personnel.
▶
The manufacturer cannot be held responsible for damages
caused to persons, things or data due to an improper or
missing ground connection.
▶
Before powering this amplier, verify that the correct voltage
rating is being used.
▶
Verify that your mains connection is capable of satisfying the
power ratings of the device.
▶
Do not spill water or other liquids into or on the amplier.
▶
Do not use this amplier if the electrical power cord is frayed
or broken.
▶
Do not remove the cover. Failing to do so will expose you to
potentially dangerous voltage.
▶
No naked ame sources such as lighted candles should be
placed on the amplier.
▶
Provide a sectioning breaker between the mains connections
and the amplier. Suggested device is 32A/250VAC, C or
D curve, 10KA (K6-K8-K10-K20) or 16A/250VAC, C or D
curve, 10KA (K2-K3)
▶
Contact the authorized service center for ordinary and
extraordinary maintenance.
▶
The power cord type is LAPP CABLE OLFLEX191 3G6 /
SJT 3XAWG10 SALCAVI (Bahoing SJT 3x16AWG or I-sheng
SGIS 3G1,5mmq for K3 - K2)
1.5 Speaker Damage
Powersoft Class D ampliers are among the most powerful
professional ampliers available and are capable of producing
much more power than many loudspeakers can handle. It is the
user’s responsibility to use speakers suitable to the amplier and
to use them in a sensible way that will not cause damage.
!
!

powersoft K10 DSP+AESOP Specifications

General

Brand	powersoft
Model	K10 DSP+AESOP
Category	Amplifier
Language	English