PRO AIR TPK 21 - User Manual

To Next Page

Pressure Dew Point Monitoring Devices!

TPK 21 / TPK 41 / TPK 61

Functional description and operating instructions

Main Page

Table of Contents2
Scope of Delivery6
General Dangers and Precautions7
Safety Instructions for Electrical Connection7
Safety Instructions for Compressed Air Systems8
Avoiding Damage to the Measuring Probe9
Calibration and Measuring Accuracy9
Important Application Notes9
Function10
Humidity Measurement in Compressed Air Systems10
Intended Application10
Application Notes11
Mounting of the Device11
Safety Instructions11
Mounting12
Procedure for Installation12
Connection at the Compressed Air Network13
Direct Stationary Assembly at the Compressed Air Line13
Stationary Assembly Via Hose13
Application of a Pre-Filter / Water Separator14
Mounting Examples14
Adjustment of Measurement Chamber Choke15
Connection of Power Supply16
For the Rarest of the Cases17
TPK Start-Up17
Operation18
Views of Unit18
Front View19
Connection to Power Supply20
- View (from Below)21
- Display21
- Description of Display22
Side View (from the Right)20
Description of Main Screen22
Description Info Screen23
- Adjustment of Display Fields24
Possible Display Variation Concerning the Different Fields25
- Personalising Password27
- Adjustment of National Languages32
- Information35
- Switching the Heating(Heater) System on and off38
- Factory Settings41
- Outputs44
- Touchscreen Calibration49
- Measurement Value Simulation52
- Statistics Reset57
- Reset Fault Memory60
- Filter63
- Units Setting66
- Setting the Date / Time69
Setting the Date69
Setting the Time73
- Configuration of Relay Adjustments77
- Setting Source (Output Parameters)79
- Setting the Relay Switching Characteristics80
- Setting the Limit Values81
- Configuration of Analog Output83
- Selection of Desired Source (Output Parameter)85
- Selection of the Desired Analog Output Value86
- Configuration of Lower Analog Output Value87
- Configuration of Upper Analog Output Value88
- Configuration of Alarm Output89
- Setting of Desired Alarm Value90
Setting of Desired Measurement - Channel (Source)90
Setting Pre-Alarm92
Setting Main-Alarm97
Setting Delay102
- Setting of Desired Alarm Value104
- Technical Datas105
- Dimensions107
- Modbus108
- Supported MODBUS Features108
- Supported MODBUS Commands108
Function Code 1 - Read Coils109
Function Code 17 - Report Slave ID109
Function Code 3 - Read Holding Registers109
Function Code 5 - Write Single Coil109
Exceptions Returned110
- Holding Registers Memory Mapping110
Function Code 16 - Write Multiple Register110
Function Code 6 - Write Single Register110
General Holding Registers Mapping111
General Coils Mapping114
Project Specific Coils Mapping114
- Data Logging115
- Appendix118
- Menu Structure119
Project Specific Holding Registers Mapping114
- Coil Address Memory Mapping114
Menu Item: Main119
Menu Item: out120
Menu Item: Alarm121
- System References and Messages122
- EG-Conformance Details123
- Guarantee123
- Accessories124
Connecting Optional Accessories125
PIN - Assignment for Conctor126
Voltage Supply from an External Source of Supply129
- Trouble Shooting Guide130
The Measured Value Is Flow Dependent and too High (I.e. too Humid)130
The Measured Value Is too High (I.e. too Humid)130
The Measured Value Is too Low (I.e. too Dry)131
The Measured Value Varies Significantly131
- Service and Calibration132

Need help?

Do you have a question about the PRO AIR TPK 21 and is the answer not in the manual?

PRO AIR TPK 21 Specifications

General

Brand	PRO AIR
Model	TPK 21
Category	Measuring Instruments
Language	English

PRO AIR TPK 21 - User Manual

Table of Contents

PRO AIR TPK 21 Specifications