Protec OPTIMAX 2010 NDT - Page 5

OPTIMAX
2010 NDT
User Manual
516
0
-
0
-
0002
PROTEC GmbH & Co. KG, In den Dorfwiesen 14, 71720 Oberstenfeld, Germany
5
von
58
6.4 Warranty .............................................................................................................................................................................................. 35
6.5 Product life time ............................................................................................................................................................................. 35
6.6 Further Information ...................................................................................................................................................................... 35
6.7 Disposal ................................................................................................................................................................................................ 35
7 Trouble Shooting ............................................................................................................... 36
7.1 Algae ...................................................................................................................................................................................................... 36
7.1.1 Excessive algae growth in water tank................................................................................................................... 36
7.2 General ................................................................................................................................................................................................. 36
7.2.1 Unit does not switch on ................................................................................................................................................ 36
7.2.2 No display but circulation pumps run.................................................................................................................. 36
7.3 Drive ....................................................................................................................................................................................................... 36
7.3.1 Film transport does not run, film processing has started ......................................................................... 36
7.3.2 Machine does not start automatically .................................................................................................................. 36
7.3.3 Machine doesn't stop automatically ..................................................................................................................... 36
7.3.4 Drive motor does not run ............................................................................................................................................ 37
7.4 Baths ...................................................................................................................................................................................................... 37
7.4.1 No circulation in bath ..................................................................................................................................................... 37
7.4.2 Developer temperature to high ............................................................................................................................... 37
7.4.3 Developer temperature to low ................................................................................................................................. 37
7.4.4 Developer temperature too low, fixer temperature too high ............................................................... 37
7.4.5 Developer bath temperature too high or too low (display shows values of 21 °C or 40 °C)
37
7.4.6 Switch-over °C to °F ......................................................................................................................................................... 37
7.4.7 Calibration of bath temperature / actual bath temperature is different from displayed
value 37
7.4.8 Developer level switch constantly displays “UU”........................................................................................... 38
7.5 Film defects ....................................................................................................................................................................................... 38
7.5.1 Films will not dry ................................................................................................................................................................ 38
7.5.2 The film does not transport correctly ................................................................................................................... 38
7.5.3 Scratches, pressure marks, dirt on film ................................................................................................................. 38
7.6 Replenishment ................................................................................................................................................................................ 38
7.6.1 Replenishment pump does not work or works insufficiently ................................................................ 38
7.7 Dryer ...................................................................................................................................................................................................... 39
7.7.1 Dryer fan does not run or runs with too low speed .................................................................................... 39
7.8 Water ..................................................................................................................................................................................................... 39
7.8.1 Rinsing water does not flow ....................................................................................................................................... 39
7.8.2 Water tank overflows ...................................................................................................................................................... 39
7.8.3 Rinsing water constantly switches on and off ................................................................................................. 39
8 Spare Parts and schematics ............................................................................................. 40
8.1 Spare Parts .......................................................................................................................................................................................... 40
8.2 Tips and Tricks .................................................................................................................................................................................. 46
8.2.1 Removal of control PCB ................................................................................................................................................. 46
8.2.2 Stop start-cycle ................................................................................................................................................................... 46
8.2.3 Display of machine information ............................................................................................................................... 46
8.2.3.1 Arrow button “Up”: ..................................................................................................................................................... 46
8.2.3.2 Arrow button “Down”: ............................................................................................................................................. 46
8.3 Schematics ......................................................................................................................................................................................... 47
9 Power Supply ..................................................................................................................... 52
9.1 Electrical connections ................................................................................................................................................................. 52
9.2 System protection ......................................................................................................................................................................... 52
9.3 Power consumption .................................................................................................................................................................... 52
10 Technical specifications ................................................................................................... 53
10.1 Protection Art and Protection Class ................................................................................................................................... 54
10.2 Environmental ................................................................................................................................................................................. 54
10.2.1 Environmental conditions during operation ................................................................................................... 54
10.2.2 Environmental Conditions for Shipping and Storage ................................................................................ 54