How to fix Provision GPS coordinates not appearing on video files?
If GPS coordinates are not appearing on your Provision video files, make sure that the “GPS OSD” is checked in the DVR web interface on the GPS settings page.
How to fix Provision 906M not recording at all?
If your Provision DVR isn't recording, it might be due to a couple of reasons. First, the SD card or SSD might not be loading correctly, refer to the section about SD card/SSD loading issues. Second, the cameras might not be set to record; check the recording settings in the web interface and ensure each camera is set to 'Auto'. Lastly, the SD/SSD might be full; free up space by enabling Overwrite or deleting alarm videos.
Why does my Provision 906M DVR have lights on but will not boot and begin recording?
If your Provision DVR has power but isn't booting up and recording, there could be a few reasons. First, the DVR might not be receiving an ignition signal; check the green ignition wire on the DVR power cable to ensure it's connected when the vehicle key is ON. Second, the ignition signal might be set improperly; DVRs are shipped with a high-level ignition setting, so if you're using a ground ignition, you'll need to change the ignition level in the interface. Finally, there might be an excessive current draw or power short on a camera, cable, or accessory; disconnect each item one at a time to see if it resolves the issue.
What to do if Provision DVR restarts or reboots on its own?
If your Provision DVR is restarting or rebooting unexpectedly, a potential cause is that the SD card or SSD is not able to be loaded by DVR. See the "DVR is not loading SD card/SSD" section for guidance. Alternatively, there might be a problem with a camera, cable, or accessory. Disconnect each component one at a time to isolate the cause, and review the log text file(s) on the SD card to determine what is causing the issue. If the issue persists, there could be a software problem with the DVR unit; in this case, contact technical support and have the log text file(s) from the SD card available.
How to fix Provision DVR filling up with video and no longer recording?
If your Provision DVR is filling up with video and stops recording (possibly beeping), it could be due to the overwrite feature not being enabled. Go to the web interface under Storage and ensure the “Overwrite” box is checked. If the video is all in the 'Alarm' folder, something might be triggering the recording too often. Ensure that triggers are set to record only occasional events. Check the Triggers, G-Force, and GPS pages to uncheck the camera recording boxes for triggers where recording isn't necessary.
Why is my Provision 906M recording some cameras but not all?
If your Provision DVR is recording some cameras but not others, the cameras that aren't recording might not be set to record in the menu. Go to the Recording settings page of the web interface and ensure that the recording is set to Auto for each camera. Also, a camera might not be working properly or could be damaged; test this by swapping the camera to another input on the DVR unit. A damaged or broken cable could also be the cause; test the cable by bypassing it with another cable or connecting the camera directly to the DVR, and replace the cable if damaged. Finally, if multiple cables are used, ensure that at least one cable is a 30 ft. Repeater cable (with an inline booster) and that the repeater is connected to the DVR, as multiple 20 ft. cables cannot be connected together.
How to correct trigger wires activating opposite from when the signal is received on Provision DVR?
If the trigger wires are activating opposite from when the signal is received on your Provision DVR, go to the Triggers page in the DVR menu and adjust the “Level” to the opposite of the current setting.
How to turn off beeping noise occasionally heard on the Provision DVR?
If you hear a beeping noise occasionally on your Provision DVR, the “Buzzer” is likely enabled for a connected trigger, G-Force, or GPS. If desired, set the buzzer setting to “Off” to disable the beeping.
What does it mean if the status light on the Provision DVR or event button is flashing red?
If the status light on the Provision DVR or the event button is flashing red, it could indicate a few issues. The DVR might not be recording because it doesn't have a disk loaded; refer to the section on loading SD cards or SSDs. Alternatively, the DVR might not be recording because the SD/SSD is full of video; free up space by enabling Overwrite in the DVR’s web interface or deleting the Alarm video on the disk. Lastly, it could be due to a software issue internally, in which case you should contact Tech Support.
Why does my Provision 906M DVR remain on after the key is turned off?
If your Provision DVR remains on after the key is turned off, the ignition power off delay is likely set on the DVR. Adjust the power off delay in the DVR menu to 0 seconds to make it turn off with the ignition.
Quick reference guide for system installation. Provides overview of steps.
Lists all components included in the DVR-906M Hybrid HD Recording Systems.
Details the PD-1900 DVR unit, its front/rear connections, and locking cage.
Guidance on choosing a mounting location and installing the DVR unit.
Steps for mounting the HD Mini-Dome camera inside a vehicle.
Guide for mounting the waterproof HD side camera for exterior coverage.
Instructions for flush mounting the HD camera in vehicle body panels.
Installing the HD camera designed to replace a vehicle's marker light.
Mounting the low profile HD camera, matching license plate hole patterns.
Guide for installing the HD heavy duty camera for rear vehicle backup.
Details connecting digital HD cameras using various cable configurations.
Mounting the versatile night vision dome camera inside a vehicle.
Mounting the wide-angle camera to the vehicle's front window.
Installing the waterproof night vision camera for rear vehicle coverage.
Mounting the super wide angle camera for superior interior vehicle coverage.
Install the stop-arm camera to capture license plates of passing vehicles.
Connects and mounts various monitor kits (5", 5" Waterproof, 7" HD).
Utilizes trigger inputs for alarm recordings, alerts, and audible alarms.
Instructions for connecting and positioning Wi-Fi antennas for connectivity.
Mounting the event marker button for easy marking of important video events.
Installs the GPS antenna to provide speed, location, and time data.
Adds or replaces the primary storage with a high-capacity Solid-State Drive.
Explains the meaning of the LED status indicators on the DVR unit.
Steps to connect the DVR via LAN or Wi-Fi for configuration and access.
Configures power, date/time, and operation control for the DVR unit.
Adjusts camera titles, alarms, flip, audio, brightness, contrast, and color.
Sets video recording, audio recording, resolution, bitrate, and file length.
Configures LAN and Wi-Fi settings, including Access Point and Client modes.
Manages disk information, formatting, and file explorer for SD/SSD storage.
Configures the stop-arm camera for automatic event generation and trigger connection.
Accessing live and recorded camera views remotely via Wi-Fi on smart devices.
Connecting and viewing camera feeds live on a monitor display via AV outputs.
Accessing and viewing recorded video files directly through the web interface.
Transferring recorded video files from SD card or SSD when Wi-Fi is not possible.
Common issues and solutions for DVR power, recording, and boot-up problems.
Resolving issues related to SD card or SSD loading, corruption, or removal.
Troubleshooting problems accessing the DVR web interface or viewing video.
Resolving issues with DVR Wi-Fi visibility, connectivity, and signal strength.
Solutions for camera viewing issues, GPS, event button, and trigger problems.
FCC compliance information for the DVR, including RF energy exposure limits.
Information on PRO-VISION warranty provisions for DVR-906M system products.
General| Hard Drive Support | 1 SATA HDD up to 6TB |
|---|---|
| Hard Drive Capacity | Up to 6TB |
| Motion Detection | Yes |
| Mobile App | Yes |
| Compression Format | H.264 |
| Remote Viewing | Yes |
| Operating Temperature | -10°C to 55°C |
| Power Supply | DC 12V |
| Recording Resolution | 720p |
To Next Page