Raymarine a68 WiFi User Manual (English)

Other manuals for Raymarine a68 WiFi

Questions and Answers:

A
Adam BanksAug 29, 2025
Why does my Raymarine a68 WiFi show a “No Fix” GPS status?
- D
  Daniel HillAug 30, 2025
  If the Raymarine Marine Equipment displays a “No Fix” GPS status icon, it could be due to several reasons. The geographic location or current conditions might be preventing a satellite fix; in this case, check periodically to see if a fix is obtained in better conditions or another geographic location. Alternatively, there may be a GPS connection fault, so ensure that external GPS connections and cabling are correct and fault free. Finally, the external GPS antenna might be poorly positioned, so ensure the GPS antenna has a clear view of the sky.
L
laurenmorganAug 29, 2025
How to fix a Raymarine Monitor radar that will not initialize (Voltage control module (VCM) stuck in “sleep mode”)?
- M
  Melanie RichmondAug 29, 2025
  If your Raymarine Monitor radar will not initialize because the Voltage Control Module (VCM) is stuck in 'sleep mode', check the power connection at the VCM. Ensure the voltage at the input is 12/24V and the voltage at the output is 40V.
R
Randall IbarraAug 28, 2025
What does it mean if my Raymarine Monitor displays 'No Data' or 'No scanner message'?
- S
  Sharon GonzalesAug 28, 2025
  If your Raymarine Monitor displays 'No Data' or 'No scanner message', check the scanner power supply cable to ensure it's sound and connections are tight and free from corrosion. Also, check that the scanner is correctly connected to a Raymarine network switch or SeaTalkhs crossover coupler, as applicable. Ensure the scanner pedestal switch is in the ON position.
J
Joseph LeAug 27, 2025
What to do if my Raymarine Monitor will not boot up (re-boot loop)?
- J
  Jacob LopezAug 27, 2025
  If your Raymarine Monitor will not boot up, it could be due to the power supply and connection issues. Also, in the unlikely event that the product's software has become corrupted, please try re-flashing the latest software from the Raymarine website. On display products, as a last resort, you can try to perform a ‘Power on Reset’; however, this will delete all settings/presets and user data and revert the unit back to factory defaults.
N
nathaniel18Aug 27, 2025
What to do if my Raymarine Monitor displays a “No Fix” GPS status icon?
- T
  Tamara WagnerAug 27, 2025
  If your Raymarine Monitor displays a 'No Fix' GPS status icon, it could be due to your geographic location or prevailing conditions preventing a satellite fix (check periodically in better conditions or another location), a GPS connection fault (ensure external GPS connections and cabling are correct), or an external GPS antenna in a poor position (ensure the GPS antenna has a clear view of the sky).
R
Raymond PerezAug 26, 2025
Why does my Raymarine Monitor not turn on or keep turning off?
- C
  Christina PatelAug 26, 2025
  Your Raymarine Monitor might not be turning on or keeps turning off due to several reasons: a blown fuse or tripped breaker (check and replace if necessary, and inspect for cable damage if fuses repeatedly blow), a poor or damaged power supply cable or connections (ensure the cable is fully inserted and locked, check for damage or corrosion, and flex the cable to check for reboots), incorrect power connection (ensure the installation instructions have been followed), or an insufficient power source (check the power supply voltage under load).
M
Michele DavidsonAug 25, 2025
How to troubleshoot Raymarine Marine Equipment that won't start?
- J
  Jeremy BeardAug 25, 2025
  If your Raymarine Marine Equipment system or part of it does not start up, there could be a power supply problem. Check the relevant fuses and breakers. Also, verify that the power supply cable is in good condition and that all connections are tight and free from corrosion. Finally, ensure that the power source provides the correct voltage and sufficient current.