Renfert POWER - User Manual

Other manuals for Renfert POWER

Questions and Answers

Hayden MilesJul 28, 2025

What to do if my Renfert Water Dispenser shows a negative filter status?

M
Michaela Macdonald MDJul 29, 2025
If a negative value appears when checking the "Filter status" on your Renfert Water Dispenser, it likely means the filter capacity wasn't reset the last time the filter was changed. To resolve this, reset the filter capacity. Note that continuing to use the filter cartridge until the replacement display appears may exceed its intended lifespan. If needed, replace the filter cartridge before the replacement display appears.

ynewtonAug 11, 2025

Why is the POWER steamer not filled in my Renfert Water Dispenser?

J
Jeremy HansonAug 11, 2025
If the POWER steamer on your Renfert Water Dispenser isn't filling, there are a couple of potential causes: * The water connections might be assembled against the direction of flow on the filter head. Check the assembly, ensuring it matches the direction indicated on both the filter head and the sensor unit. * The water supply could be turned off. Make sure to turn on the water supply.

Summary

1 Introduction

1.1 Symbols used

Explains symbols used in the manual and on the equipment for warnings and instructions.

2 Safety

2.1 Intended use

Describes the specific purpose and application of the POWER steamer water softener.

2.2 Improper use

Details incorrect usage that could lead to safety risks or damage.

2.3 Ambient conditions for storage and transport

Specifies required temperature and humidity for storage and transport.

2.4.1 General information

Provides general safety advice and checks for cables, tubes, and housing.

2.4.2 Specific information

Lists specific precautions for water quality, component handling, and system pressure.

2.5 Authorized persons

Defines who is permitted to perform installation, maintenance, and repairs.

2.6 Disclaimer

Outlines limitations of liability for Renfert GmbH under specific conditions.

3 General description

3.1 Assemblies and functional elements

Identifies and illustrates all components of the water softener system.

3.2 Scope of delivery

Lists all items included in the product package.

3.3 Accessories

Lists available optional accessories for the water softener.

4 Startup

4.1 Unpacking

Instructions for safely removing the unit and accessories from the packaging.

4.2 Installation

Step-by-step guide for installing the filter system, including location and preparation.

4.3.1 Using the test strips

Explains how to use test strips to determine water hardness.

4.3.2 Setting the blend level

Guides on adjusting the blend valve to match water hardness for optimal performance.

4.4 Assembling the filter head; flowmeter; filter cartridge

Detailed steps for connecting the main components of the water softener system.

4.5.1 Entering the filter capacity

Instructions for inputting the filter cartridge capacity into the display unit.

5 Operation

5.1 Replacing a filter cartridge

Step-by-step guide for removing and installing a new filter cartridge.

5.1.1 Resetting the counter; checking the filter capacity

How to reset the system counter after cartridge replacement.

5.2.1 Selecting a menu item

Navigating through the display unit's menu options.

5.2.2 Filter status display

How to view the current status and remaining capacity of the filter.

5.2.3 Reset the filter capacity (when replacing the filter)

Procedure for resetting the filter capacity after replacement.

5.2.4 Entering the filter capacity

Detailed steps for inputting the correct filter capacity value.

5.2.5 Counter reading (when inserting the cartridge)

How to view historical counter readings for previous cartridges.

5.2.6 Alarm

How to configure and interpret system alarms.

5.2.7 Setting the unit (liters or gallons)

How to switch between metric (liters) and imperial (gallons) units.

5.2.8 Setting the pulse per liter

Configuration setting for pulse output, for service purposes.

6 Cleaning; Maintenance

6.1 Flushing the system

Procedure for flushing the system after maintenance or periods of disuse.

6.2 Spare parts

Information on ordering replacement parts and consumables.

8 Technical data

8.1 Filter unit

Technical specifications for the filter unit.

8.2 Flowmeter

Technical specifications for the flowmeter component.

Brand	Renfert
Model	POWER
Category	Water Dispenser
Mains voltage	230 V
Frequency	50/60 Hz
Tank capacity	5 l
Material	Plastic
Color	White

Brand

Renfert

Model

POWER