To Next PageTo Next Page
Need help?Do you have a question about the Rinnai RUR98i and is the answer not in the manual?
General| Type | Tankless |
|---|---|
| Category | Residential |
| Fuel Type | Natural Gas/Propane |
| Maximum Flow Rate | 9.8 GPM |
| Condensing | Yes |
| Gas Connection | 3/4" NPT |
| Water Connection | 3/4" NPT |
| Ignition Type | Electronic |
| Warranty | 12 years heat exchanger, 5 years parts, 1 year labor |
| Maximum BTU Input | 199, 000 BTU/h |
| Minimum BTU Input | 15, 000 BTU/h |
| Electrical Requirements | 120V, 60Hz |
| Temperature Range | 98°F - 140°F |
| GPM at 45°F Rise | 8.4 GPM |
Defines safety alert symbols like Danger, Warning, and Caution.
Provides critical safety precautions for operation and maintenance.
Highlights burn hazard warnings and precautions.
Discloses potential chemical exposure related to California regulations.
Outlines the necessary skills and training for qualified installers.
Covers essential installation rules and requirements for all installations.
Lists components provided with the water heater unit.
Lists all necessary tools required for the installation process.
Lists all required materials for the installation process.
Advises on checking water quality to prevent heat exchanger damage.
Discusses site conditions and potential impacts of corrosive air.
Explains measures to prevent freezing damage to the unit and water lines.
Provides step-by-step instructions for physically mounting the unit.
Details how to remove the front panel for access to internal components.
Lists manufacturers and products certified for venting.
Lists prohibited practices for vent system installation.
Lists required practices for vent system installation.
Provides details for installing a concentric vent system setup.
Provides details for installing a twin pipe PVC/CPVC vent system.
Specific guidance for horizontal flue installation with concentric venting.
Specific guidance for vertical flue installation with concentric venting.
Key factors and guidelines for choosing vent termination locations.
Vent length calculation method using a worksheet.
Vent length calculation method using tables.
Lists specific parts required for 3-inch PVC/CPVC vent assembly.
Lists specific parts required for 4-inch PVC/CPVC vent assembly.
Overview of the different types of approved vent termination configurations.
General steps and considerations for installing vent terminations.
Provides a step-by-step process for installing the vent system.
General information regarding twin pipe PVC/CPVC vent terminations.
Specific guidance for sidewall vent terminations using tee or snorkel.
Specific guidance for roof vent terminations using tee or 'U' configurations.
Steps for properly cementing PVC/CPVC joints for vent assembly.
Table listing vent components and their equivalent lengths for sizing.
Lists prohibited practices for condensate drainage.
Lists required practices for condensate drainage.
A checklist for verifying proper venting and condensate management.
Guidelines for installing the safety pressure relief valve.
General rules and requirements for water piping installation.
Steps for installing the included isolation valves.
Steps for installing the pressure relief valve.
A checklist for verifying correct plumbing installation.
Explains how the recirculation system operates based on settings.
Details the dedicated return line recirculation mode.
Details the thermal by-pass valve used in cross-over recirculation.
Covers essential rules for connecting the gas supply.
Guidance on calculating and selecting the correct gas pipe size.
Recommendations for optimal placement of the temperature controller.
Specifies maximum cable lengths for controller wiring.
A comprehensive pre-operation checklist for installation verification.
Key technical data and performance ratings of the water heater.
Introductory information about the water heater's features and safety.
Step-by-step guide for starting and using the water heater.
Detailed steps for setting the desired water temperature.
Table showing selectable temperature ranges and modes.
Guide for setting the controller's internal clock.
Steps for programming the timer for circulation functions.
Explanation of the timer-based circulation feature.
How to manually override or temporarily alter the circulation timer.
Details on power saving, beep, clock, and temperature scale settings.
How to lock or unlock the controller buttons for safety.
How to set priority among multiple connected temperature controllers.
Instructions for cleaning internal components, burners, and air passages.
Information on scale issues and flushing the heat exchanger.
Procedure for cleaning the inlet water filters.
How to visually check the burner flame for correct operation.
Essential measures to protect the unit and water lines from freezing.
Steps for manually draining the unit for maintenance or winterization.
Procedure to access diagnostic codes on the controller.
Mandated rules for installing carbon monoxide detectors.
Defines the scope and terms of the product's warranty coverage.
Specifies the warranty periods for different components and applications.
Lists exclusions and limitations of the product warranty.
Conditions for extending the labor warranty in residential settings.
