Roland FR-4X - Page 62

62
Menu Options
Parameter Explanation/Value
Attack
(Attack time)
(Not for VTW Organ Tone)
&
“Right Hand Orchestra Part
Parameters (Orchestra Edit)” (p. 53)
Decay
(Decay time)
Release
(Release time)
Cutoff
(Cutoff)
Reso
(Resonance)
Vib Dly
(Vibrato Delay)
Vib Dept
(Vibrato Depth)
Vib Rate
(Vibrato Rate)
ExpPedal
(Expression Pedal)
Select “Off ” If you want to use the
bellows for expressive purposes.
Select “On” if you want control the
expression by foot purchasing an optional
MIDI foot controller (e.g. FC-300).
Off, On
Touch
(Touch)
(Not for VTW Organ Tone)
This parameter allows you to specify
the velocity sensitivity of the Left Hand
section keys when they are used to play
Orchestral Chord sounds.
NOTE
5 Only when you select a tone that can be
controlled only by the keyboard, you can
set the “Touch” (When a tone that can
not be set is selected it will be displayed
as “----”).
For details regarding these sounds
refer to the”Tone & Drum Kit List “
supplementary manual.
&
http://www.roland.com/manuals/
5 It has no effect on the VTW Organ sounds.
5 There are several sounds which
the difference in the velocities is
incomprehensible.
“FIX.L (Fixed Low)”: The
velocity value will always
be 50 (0x32) regardless of
the strength with which
you play the keyboard.
“FIX.M (Fixed Med)”: The
velocity value will always
be 80 (0x50) regardless of
the strength with which
you play the keyboard.
“FIX.H (Fixed High)”: The
velocity value will always
be 127 (0x7F) regardless
of the strength with which
you play the keyboard.
“LOW (Low)”: The velocity
value will not be less than
33 (0x21) even when
you play the most weak
keyboard. You get a certain
amount of volume even
if you play lightly on the
keyboard.
Parameter Explanation/Value
Touch
(Touchh)
“MED (Medium)”: The
velocity value will not be
less than 17 (0x11) even
when you play the most
weak keyboard. This is the
middle of the “Low”and
the “High.”
“HIGH (High)” : The
velocity value is controlled
in the range of 1 (0x01) ~
127 (0x7F) by the strength
with which you play the
keyboard.This setting is
the most wide range of
velocity control.
“F.L+B (Fixed
Low+Bellows)”: You will
control the velocity in the
movement of the bellows
at the timing you play the
keyboard. However, the
velocity value will not be
less than 20 (0x14).
“F.M+B (Fixed
Med.+Bellows)”: ou will
control the velocity in the
movement of the bellows
at the timing you play the
keyboard. However, the
velocity value will not be
less than 50 (0x32).
“F.M+B (Fixed
Med.+Bellows)”: ou will
control the velocity in the
movement of the bellows
at the timing you play the
keyboard. However, the
velocity value will not be
less than 50 (0x32).
“BELW (Bellows)”: You will
control the velocity in the
movement of the bellows
at the timing you play the
keyboard.
MIDI TX
(MIDI Tx)
Pressing the [ENTER/YES] button lets you
make MIDI TX settings for the orchestra
chord part.
MIDI TX
These parameters specify MIDI transmission for the orchestra chord
part.
These settings can be saved for each set, and you can use different
MIDI settings for each register within the set.
Parameter Explanation/Value
Note Tx
(Note Tx)
For details, refer to “Accordion Edit -
MIDI TX” (p. 46).
Octave
(Octave)