Roland JUNO-X - [SCENE] Button Is Lit)

30
Correspondence Between Controllers and Parameters
Section Controller Parameter
Destination or
operation when used
with the [SHIFT] button
PORTAMENTO
1
ON Porta Sw
TONE COMMON EDIT:
Porta Sw
2
TIME Porta Time
SCENE PART EDIT:
CTRL: Porta Time
LFO
3
PITCH
Select PITCH LFO
(*1)
-
4
FILTER
Select FILTER LFO
(*1)
-
5
AMP Select AMP LFO (*1) -
6
RATE Vib Rate
SCENE PART EDIT:
MODIFY: Vib Rate
7
DELAY TIME Vib Delay
SCENE PART EDIT:
MODIFY: Vib Delay
8
DEPTH
If “PITCH-LFO” is
selected
Pit LFO Dep
SCENE PART EDIT:
LFO: Pit LFO Dep
If “FILTER-LFO” is
selected
Flt LFO Dep
SCENE PART EDIT:
LFO: Flt LFO Dep
If “AMP-LFO” is selected
Amp LFO Dep
SCENE PART EDIT:
LFO: Amp LFO Dep
OSC
9
PWM/MOD Fine Tune
SCENE PART EDIT:
PITCH: Fine Tune
10
Partial1 Level
TONE EDIT PARTIAL1:
Tone PTL: Level
11
Partial2 Level
TONE EDIT PARTIAL2:
Tone PTL: Level
12
SUB Partial3 Level
TONE EDIT PARTIAL3:
Tone PTL: Level
13
NOISE Partial4 Level
TONE EDIT PARTIAL4:
Tone PTL: Level
14
PITCH Coarse Tune
SCENE PART EDIT:
PITCH: Coarse Tune
FILTER
15
FREQ Cuto
SCENE PART EDIT:
MODIFY: Cuto
16
RES Resonance
SCENE PART EDIT:
MODIFY: Resonance
17
KYBD Flt KeyFllw
SCENE PART EDIT:
FILTER: Flt KeyFllw
AMP
18
LEVEL
If “Part1–4” is selected
Level
TONE COMMON EDIT:
Level
If “PartR” is selected
Part Level
SCENE PART EDIT: Part
Level
ENV
19
PITCH
Select PITCH ENV
(*2)
-
20
FILTER
Select FILTER ENV
(*2)
-
21
AMP Select AMP ENV (*2) -
Section Controller Parameter
Destination or
operation when used
with the [SHIFT] button
ENV
22
A
If “PITCH ENV” is
selected
Pit Attack
SCENE PART EDIT:
PITCH: Pit Attack
If “FILTER ENV” is
selected
Flt Attack
SCENE PART EDIT:
FILTER: Flt Attack
If “AMP ENV” is selected
Amp Attack
SCENE PART EDIT:
AMP: Amp Attack
23
D
If “PITCH” is selected
Pit Decay
SCENE PART EDIT:
PITCH: Pit Decay
If “FILTER ENV” is
selected
Flt Decay
SCENE PART EDIT:
FILTER: Flt Decay
If “AMP ENV” is selected
Amp Decay
SCENE PART EDIT:
AMP: Amp Decay
24
S
If “PITCH” is selected
Pit Sustain
SCENE PART EDIT:
PITCH: Pit Sustain
If “FILTER ENV” is
selected
Flt Sustain
SCENE PART EDIT:
FILTER: Flt Sustain
If “AMP ENV” is selected
Amp Sustain
SCENE PART EDIT:
AMP: Amp Sustain
25
R
If “PITCH” is selected
Pit Release
SCENE PART EDIT:
PITCH: Pit Release
If “FILTER ENV” is
selected
Flt Release
SCENE PART EDIT:
FILTER: Flt Release
If “AMP ENV” is selected
Amp Release
SCENE PART EDIT:
AMP: Amp Release
26
DEPTH
If “PITCH ENV” is
selected
Pit ENV Depth
SCENE PART EDIT:
PITCH: Pit ENV Depth
If “FILTER ENV” is
selected
Flt ENV Depth
SCENE PART EDIT:
FILTER: Flt ENV Depth
XV-5080, RD-PIANO, and Other Tones (When the [SCENE] Button Is Lit)
6
1
2
10 12 14 13 9 17
18
11 7 8 15 16
26
27 28
22 23 24 25
3 4 5 19 20 21
29 30 31 32