Roland JUNO-X - Exporting Tones; Exporting Scenes

47
Convenient Functions (UTILITY Screen)
6. Use the [ÇSELECTÉ] knob to select the scene you
wish to import, and use the [- VALUE +] knob to select
it with a check mark.
To select/deselect all scenes
Hold down the [SHIFT] button and turn the [- VALUE +] knob.
To specify a range of scenes to select/deselect
Press the [ENTER] button at the beginning of the range, and then
press [ENTER] while holding the [SHIFT] button at the end of the
range.
7. Press the [Ë] button.
8. Use the [ÇSELECTÉ] knob to select where to import
the scene, and press the [ENTER] (INIT) button to
select it with a check mark.
NOTE
¹ Use caution, as this overwrites the scene that’s already in the import destination.
¹ If there are not enough scenes in the import destination to save the data to be
imported, not all of the scenes selected are imported.
¹ You can check the number of scenes at the top right-hand part of the screen.
Number of scenes in import destination and source
¹ If a scene named “INIT SCENE” already exists, this is automatically selected as the
import destination scene with a check mark.
* If a scene named “INIT SCENE” already exists, it is automatically selected
as the import destination scene, even it was previously edited.
¹ To leave the scene as-is, clear the check mark.
9. Press the [Ë] button.
10. To execute, use the [- VALUE +] knob to select “OK,”
and then press the [ENTER] (INIT) button.
When importing, the tone is saved with the name “INIT TONE.”
The display shows “Import Scene Completed!” when importing
is done.
* If a user tone is being used by the scene of the import destination, you
can select whether to import that user tone as well.
* Never turn o the power or disconnect the USB ash drive when
“Executing...” or a similar message is shown on the screen, as the unit is
processing data.
Exporting Tones
You can export the user tone data to an SVZ le.
* You can also export tones from models.
1. Connect a USB ash drive.
2. Press the [MENU] (WRITE) button.
3. Use the [ÇSELECTÉ] knob to select “UTILITY,” and
then press the [ENTER] (INIT) button.
4. Use the [ÇSELECTÉ] knob to select “IMPORT/
EXPORT,” and then press the [ENTER] (INIT) button.
5. Use the [ÇSELECTÉ] knob to select “EXPORT TONE,”
and then press the [ENTER] (INIT) button.
6. Use the [ÇSELECTÉ] knob to select where to export
the tone from, and press the [ENTER] (INIT) button to
select it with a check mark.
To select/deselect all tones
Hold down the [SHIFT] button and turn the [- VALUE +] knob.
To specify a range of tones to select/deselect
Press the [ENTER] (INIT) button at the beginning of the range, and
then press [ENTER] (INIT) button while holding the [SHIFT] button at
the end of the range.
7. Press the [Ë] button.
8. Move the cursor using the [Í] [Ë] buttons, and use
the [- VALUE +] knob to edit the characters.
9. Once you’ve entered the lename, press the [ENTER]
(INIT) button.
A conrmation message appears.
If you decide to cancel, press the [EXIT] button.
10. To execute, use the [- VALUE +] knob to select “OK,”
and then press the [ENTER] (INIT) button.
The scenes are exported to the “ROLAND/SOUND” folder on
your USB ash drive.
The display shows “Export Tone Completed!” when exporting is
done.
* Never turn o the power or disconnect the USB ash drive during a
process, such as while the “Executing…” display is shown.
Exporting Scenes
You can export the scene data to an SVD le.
1. Connect a USB ash drive.
2. Press the [MENU] (WRITE) button.
3. Use the [ÇSELECTÉ] knob to select “UTILITY,” and
then press the [ENTER] (INIT) button.
4. Use the [ÇSELECTÉ] knob to select “IMPORT/
EXPORT,” and then press the [ENTER] (INIT) button.
5. Use the [ÇSELECTÉ] knob to select “EXPORT SCENE,”
and then press the [ENTER] (INIT) button.
6. Use the [ÇSELECTÉ] knob to select where to export
the scene from, and press the [ENTER] (INIT) button to
select it with a check mark.
To select/deselect all scenes
Hold down the [SHIFT] button and turn the [- VALUE +] knob.
To specify a range of scenes to select/deselect
Press the [ENTER] (INIT) button at the beginning of the range, and
then press [ENTER] (INIT) while holding the [SHIFT] button at the end
of the range.
7. Press the [Ë] button.
8. Move the cursor using the [Í] [Ë] buttons, and use
the [- VALUE +] knob to edit the characters.
9. Once you’ve entered the lename, press the [ENTER]
(INIT) button.
A conrmation message appears.
If you decide to cancel, press the [EXIT] button.
10. To execute, use the [- VALUE +] knob to select “OK,”
and then press the [ENTER] (INIT) button.
The scenes are exported to the “ROLAND/SOUND” folder
on your USB ash drive. The display shows “Export Scene
Completed!” when exporting is done.
* Never turn o the power or disconnect the USB ash drive during a
process, such as while the “Executing…” display is shown.