Roland JUNO-X - Ä Using the IMPORT;EXPORT Function; Importing Tones; Importing Scenes

46
Convenient Functions (UTILITY Screen)
Using the IMPORT/EXPORT Function
Importing Tones
You can import tones that you’ve downloaded from Roland Cloud (*)
or exported from other instruments into the JUNO-X as additional
tones.
* You can also import tones from models.
When you import a tone that does not belong to a model, the model
name is saved as “Z-Core.”
(*) What is Roland Cloud?
Roland Cloud is a cloud-based subscription service that oers high-quality plug-in sound
engines and software for music production.
https://www.roland.com/global/categories/roland_cloud/
Saving tones to USB ash drive
1.
Prepare a SVZ le with the tones you’ve downloaded
or exported from other models by using their export
function, which you’ll import into the JUNO-X.
2. Connect a USB ash drive to your computer.
* If this is the rst time you’re using the USB ash drive, format it on the
JUNO-X.
Ø “Formatting a USB Flash Drive (FORMAT USB MEMORY)” (p. 45)
3. Save the SVZ le to the “ROLAND/SOUND” folder on
your USB ash drive.
4. Remove the USB ash drive from your computer and
connect it to the JUNO-X.
Importing tones into the JUNO-X
1.
Press the [MENU] (WRITE) button.
2. Use the [ÇSELECTÉ] knob to select “UTILITY,” and
then press the [ENTER] (INIT) button.
3. Use the [ÇSELECTÉ] knob to select “IMPORT/
EXPORT,” and then press the [ENTER] (INIT) button.
4. Use the [ÇSELECTÉ] knob to select “IMPORT TONE,”
and then press the [ENTER] (INIT) button.
5. Use the [ÇSELECTÉ] knob to select the le
containing the tone you wish to import, and press the
[Ë] button.
The number of tones that are saved in that le are shown in
parentheses.
6. Use the [ÇSELECTÉ] knob to select the tone you
wish to import, and use the [- VALUE +] knob to select
it with a check mark.
To select/deselect all tones
Hold down the [SHIFT] button and turn the [- VALUE +] knob.
To specify a range of tones to select/deselect
Press the [ENTER] (INIT) button at the beginning of the range, and
then press [ENTER] (INIT) while holding the [SHIFT] button at the end
of the range.
7. Press the [Ë] button.
8. Use the [ÇSELECTÉ] knob to select where to import
the tone, and press the [ENTER] (INIT) button to select
it with a check mark.
NOTE
¹ Tones that are being used in a scene are marked with an asterisk (*).
¹ Use caution, as this overwrites the tone you select that’s already in the import
destination.
¹ If there are not enough locations in the import destination to save the data to be
imported, not all of the tones selected are imported.
¹ You can check the number of tones at the top right-hand part of the screen.
Number of tones in import destination and source
¹ If a tone named “INIT TONE” already exists, this is automatically selected with a
check mark as the import destination tone.
* If a tone named “INIT TONE” already exists, it is automatically selected as
the import destination tone, even it was previously edited.
¹ To leave the tone as-is, clear the check mark.
9. Press the [Ë] button.
10. To execute, use the [- VALUE +] knob to select “OK,”
and then press the [ENTER] (INIT) button.
The display shows “Import Tone Completed!” when importing
is done.
* Never turn o the power or disconnect the USB ash drive when
“Executing...” or a similar message is shown on the screen, as the unit is
processing data.
Importing Scenes
You can import scenes into the JUNO-X as additional scenes that were
exported from the JUNO-X.
* You can also import scenes from a backup le.
Saving scenes to USB ash drive
1.
Prepare a SVD le with the scenes you’ve exported
from the JUNO-X by using its export function, which
you’ll import into the JUNO-X.
2. Connect a USB ash drive to your computer.
* If this is the rst time you’re using the USB ash drive, format it on the
JUNO-X.
Ø “Formatting a USB Flash Drive (FORMAT USB MEMORY)” (p. 45)
3. Save the SVD le to the “ROLAND/SOUND” folder on
your USB ash drive.
4. Remove the USB ash drive from your computer and
connect it to the JUNO-X.
Importing scenes into the JUNO-X
1.
Press the [MENU] (WRITE) button.
2. Use the [ÇSELECTÉ] knob to select “UTILITY,” and
then press the [ENTER] (INIT) button.
3. Use the [ÇSELECTÉ] knob to select “IMPORT/
EXPORT,” and then press the [ENTER] (INIT) button.
4. Use the [ÇSELECTÉ] knob to select “IMPORT SCENE,”
and then press the [ENTER] (INIT) button.
5. Use the [ÇSELECTÉ] knob to select the le
containing the scene you wish to import, and press
the [Ë] button.