Roland JUNO-X - Page 35

35
Correspondence Between Controllers and Parameters
Section Controller Parameter
Operation when used
with the [SHIFT] button
(*1)
EFFECTS
22
MFX
Assign Parameters
(*3)
If SCENE PART MFX:
FllwToneMFX is “ON”
Parameter
corresponding to “TONE
MFX” (*4)
If SCENE PART MFX:
FllwToneMFX is “OFF”
Parameter
corresponding to
“SCENE PART MFX” (*4)
23
DELAY
If SCENE PART EDIT: Output
is “THRU”
Dly Send
SCENE PART EDIT:
Dly Send
If SCENE PART EDIT: Output
is “DRIVE”
Dly Send Lev
SCENE EFFECT:
OD: Dly Send Lev
24
TIME
If SYSTEM EFFECT: Dly:
Source is “SYS,” and “Dly
Sync” is “OFF”
Dly Msec
SYSTEM EFFECT:
Dly: Dly Msec
If SYSTEM EFFECT: Dly:
Source is “SYS,” and “Dly
Sync” is “ON”
Dly Note
SYSTEM EFFECT:
Dly: Dly Note
If SYSTEM EFFECT: Dly:
Source is “SCENE,” and “Dly
Sync” is “OFF”
Dly Msec
SCENE EFFECT:
Dly: Dly Msec
If SYSTEM EFFECT: Dly:
Source is “SCENE,” and “Dly
Sync” is “ON”
Dly Note
SCENE EFFECT:
Dly: Dly Note
FEEDBACK
If SYSTEM EFFECT: Dly:
Source is “SYS”
Feedback (*2)
SYSTEM EFFECT:
Dly: Feedback
If SYSTEM EFFECT: Dly:
Source is “SCENE”
Feedback (*2)
SCENE EFFECT:
Dly: Feedback
PART/FUNC
25
MFX MFX Switch
If SCENE PART MFX:
FllwToneMFX is “ON”
TONE MFX: Switch
If SCENE PART MFX:
FllwToneMFX is “OFF”
SCENE PART MFX:
Switch
26
DELAY Delay Switch
If SYSTEM EFFECT: Dly:
Source is “SCENE”
SCENE EFFECT:
Dly: Switch
If SYSTEM EFFECT: Dly:
Source is “SYS”
SYSTEM EFFECT:
Dly: Switch
27
REVERB Reverb Switch
If SYSTEM EFFECT: Rev:
Source is “SCENE”
SCENE EFFECT:
Rev: Switch
If SYSTEM EFFECT: Rev:
Source is “SYS”
SYSTEM EFFECT:
Rev: Switch
28
CHORUS Chorus Switch
If SYSTEM EFFECT: Cho:
Source is “SCENE”
SCENE EFFECT:
Cho: Switch
If SYSTEM EFFECT: Cho:
Source is “SYS”
SYSTEM EFFECT:
Cho: Switch
KEY MODE
29
SINGLE SINGLE -
30
SPLIT SPLIT -
31
DUAL DUAL -
L/R DUAL L/R DUAL (*2) -
Section Controller Parameter
Operation when used
with the [SHIFT] button
(*1)
CTRL
32
SL1
Assigned function
(*4)
SCENE COMMON EDIT:
ASSIGN: SL1
33
SL2
Assigned function
(*4)
SCENE COMMON EDIT:
ASSIGN: SL2
34
S1
Assigned function
(*4)
SCENE COMMON EDIT:
ASSIGN: S1 Func
35
S2
Assigned function
(*4)
SCENE COMMON EDIT:
ASSIGN: S2 Func
36
S3
Assigned function
(*4)
SCENE COMMON EDIT:
ASSIGN: S3 Func
(*1): For parameters whose function can be assigned, the factory-set
destination is listed. If the system parameter “Source” setting of
a controller is set to “SYSTEM,” you’ll move to the corresponding
SYSTEM parameter.
Ø “Parameter Guide” (PDF)
(*2): Only enabled in “FUNC” mode.
(*3): The corresponding parameter diers depending on the Type of
MFX.
Ø“MFX Assign Parameters” (p. 36)
(*4): The functions that can be assigned dier depending on the
controller.
Ø“List of functions that can be assigned to the controllers”
(p. 41)