4
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and
observe the following:
Power Supply
301
•
Do not use this unit on the same power circuit with
any device that will generate line noise (such as an
electric motor or variable lighting system).
302
• The AC adaptor will begin to generate heat after
long hours of consecutive use. This is normal, and is
not a cause for concern.
303a
• The use of an AC adaptor is recommended as the
unit’s power consumption is relatively high. Should
you prefer to use batteries, please use the alkaline
type.
304a
• When installing or replacing batteries, always turn
off the power on this unit and disconnect any other
devices you may have connected. This way, you can
prevent malfunction and/or damage to speakers or
other devices.
306b
• Batteries are supplied with the unit. The life of these
batteries may be limited, however, since their
primary purpose was to enable testing.
307
• Before connecting this unit to other devices, turn off
the power to all units. This will help prevent
malfunctions and/or damage to speakers or other
devices.
Placement
352a
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of
such receivers.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the
vicinity of this unit. Such noise could occur when
receiving or initiating a call, or while conversing.
Should you experience such problems, you should
relocate such wireless devices so they are at a
greater distance from this unit, or switch them off.
354a
• Do not expose the unit to direct sunlight, place it
near devices that radiate heat, leave it inside an
enclosed vehicle, or otherwise subject it to temper-
ature extremes. Excessive heat can deform or
discolor the unit.
355
• To avoid possible breakdown, do not use the unit in
a wet area, such as an area exposed to rain or other
moisture.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry
cloth or one that has been slightly dampened with
water. To remove stubborn dirt, use a cloth impreg-
nated with a mild, non-abrasive detergent. After-
wards, be sure to wipe the unit thoroughly with a
soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of
any kind, to avoid the possibility of discoloration
and/or deformation.
Additional Precautions
553
• Use a reasonable amount of care when using the
unit’s buttons, sliders, or other controls; and when
using its jacks and connectors. Rough handling can
lead to malfunctions.
554
• Never strike or apply strong pressure to the display.
556
• When connecting / disconnecting all cables, grasp
the connector itself—never pull on the cable. This
way you will avoid causing shorts, or damage to the
cable’s internal elements.
558a
• To avoid disturbing your neighbors, try to keep the
unit’s volume at reasonable levels. You may prefer
to use headphones, so you do not need to be
concerned about those around you (especially when
it is late at night).
558d
• This instrument is designed to minimize the extra-
neous sounds produced when it’s played. However,
since sound vibrations can be transmitted through
floors and walls to a greater degree than expected,
take care not to allow these sounds to become a
nuisance to neighbors, especially when performing
at night and when using headphones.
559a
• When you need to transport the unit, package it in
the box (including padding) that it came in, if
possible. Otherwise, you will need to use equivalent
packaging materials.
562
• Use the included cable or a cable from Roland to
make the connection. If using some other make of
connection cable, please note the following precau-
tions.
•
Some connection cables contain resistors. Do not
use cables that incorporate resistors for connecting
to this unit. Since the sensitivity of the pad will be
diminished, the sound may become extremely soft
or even inaudible. For information on cable specifi-
cations, contact the manufacturer of the cable.
add1
• The hoop’s rubber portion is an expendable item,
whose performance deteriorates with extended use.
Continued use of this rubber component beyond its
useful service life may result in malfunction or
damage to the hoop. If this occurs, replace the hoop
and insert.
For more on replacing the hoop rubber, consult with
your retailer, the nearest Roland Service Center, or
an authorized Roland distributor, as listed on the
"Information" page.
add2
• Do not apply excessive force to the sensor located
below the center of the head. Doing so can interfere
with accurate detection, and may damage it.
add3
• Due to the nature of the materials used in the sensor,
changes in room temperature may affect the sensi-
tivity of the sensor.
add4
• Be sure to adjust the head tension before using the
RP-2. Striking the pad while the head is loosened
may damage the sensor and head.
985
• The explanations in this manual include illustrations
that depict what should typically be shown by the
display. Note, however, that your unit may incor-
porate a newer, enhanced version of the system (e.g.,
includes newer sounds), so what you actually see in
the display may not always match what appears in
the manual.
To Next Page
Loading...
