Sanyo PLC-XF60A - Page 62

- 62 -
Electrical Adjustments
Group No. Item Function Range Initial Value
940 For factory use
960 DXOUT XGA[SXGA]
0 R
0~ 1023[0~511]
520 [237]
1 G
0~ 1023[0~511]
520 [237]
2 B
0~ 1023[0~511]
520 [237]
970 Reference for Sample Hold
0 R 1 ~ 12 6 [3]
1 G 1 ~ 12 6 [3]
0 B 1 ~ 12 6 [3]
971 Panel Variation Companzation
0 (Not used)
1 DAC1 0 ~ 255 0 Effective only SXGA+
2 DAC2 0 ~ 255 0 Effective only SXGA+
3 DAC3 0 ~ 255 0 Effective only SXGA+
4 (Not used)
5 (Not used)
6 (Not used)
7 (Not used)
8 (Not used)
972 Timming Generation Part XGA[SXGA]
0 ENBX*R Driver Enable Pluse 0~127 [0~63] 4 [10]
1 ENBX*G Driver Enable Pluse 0~127 [0~63] 4 [10]
2 ENBX*B Driver Enable Pluse 0~127 [0~63] 4 [10]
3 H-Change Position for CLYOUT, DYOUT, FRP 0 ~ 31 5 [7]
4 NRG POSI Drive Pulse Position for Panel Driver Circuit 0 ~ 127 44 [44]
5 NRG WIDTH Drive Pulse width for Panel Driver Circuit 0 ~ 255 120 [68]
6 HSYNC DELAY Setting of HSYNC Delay 0 ~ 3 0 [0]
7 VSYNC EDGE SW Switch VSYNC Effective Edge 0 ~ 1 0 [0]
8 HSYNC EDGE SW Switch HSYNC Effective Edge 0 ~ 1 0 [0]
9 DYOUTR Shift Data R for Panel Y 0 ~ 511 0 [2]
10 DYOUTG Shift Data G for Panel Y 0 ~ 511 0 [2]
11 DYOUTB Shift Data B for Panel Y 0 ~ 511 0 [2]
973 Video Processing Common XGA[SXGA]
0 Start position for reference voltage insertion gate 2 ~ 513 56 [25]
1 Width for the reference voltage insertion gate 0 ~ 511 180 [118]
2 Horizontal-mask cancel position
0~1023 [0~2047]
272 [410]
3 Horizontal display range
0~2047 [0~4095]
2047 [1480]
4 Setting of OSD function insertion position 0 ~ 3 2 [0]
5 Video Mute 0 ~ 2047 0 [0]
6 Vertical-musk display range control 0 ~ 2047 2047 [2047]
974 Video Processing V-line correction XGA[SXGA]
0 Correction switch (V-line shading, ghost) 0 ~ 1 1 [1]
1 V-line shading offset correction-switch 0 ~ 1 1 [1]
2 V-line shading block edge correction-switch 0 ~ 1 1 [1]
3 Progressive ghost correction-switch 0 ~ 1 1 [1]
4 Block ghost correction-switch 0 ~ 1 1 [1]
5 Reverse ghost crrection-switch 0 ~ 1 1 [1]
6 H-crosstalk correction-switch 0 ~ 1 1 [1]
7 Reference position setting for V-line shading correction [R] 0 ~ 11 8 [1]
8 Reference position setting for V-line shading correction [G] 0 ~ 11 8 [1]
9 Reference position setting for V-line shading correction [B] 0 ~ 11 8 [1]
10 V-line shading adjutment mode [R] 0 ~ 1 0 [0]
11 V-line shading adjutment mode [G] 0 ~ 1 0 [0]
12 V-line shading adjutment mode [B] 0 ~ 1 0 [0]
13 Adjustment steps setting for V-line shading adjustment 0 ~ 4095 0 [0]
14 Correction value setting for V-line shading [R0] -512 ~ 511 28 [12]
15 Correction value setting for V-line shading [R1] -512 ~ 511 16 [6]
16 Correction value setting for V-line shading [R2] -512 ~ 511 5 [0]
17 Correction value setting for V-line shading [R3] -512 ~ 511 -10 [-4]
18 Correction value setting for V-line shading [R4] -512 ~ 511 -16 [-4]
19 Correction value setting for V-line shading [G0] -512 ~ 511 28 [12]
20 Correction value setting for V-line shading [G1] -512 ~ 511 16 [6]
21 Correction value setting for V-line shading [G2] -512 ~ 511 5 [0]
22 Correction value setting for V-line shading [G3] -512 ~ 511 -10 [-4]
23 Correction value setting for V-line shading [G4] -512 ~ 511 -16 [-4]
24 Correction value setting for V-line shading [B0] -512 ~ 511 28 [12]
25 Correction value setting for V-line shading [B1] -512 ~ 511 16 [6]
26 Correction value setting for V-line shading [B2] -512 ~ 511 5 [0]
27 Correction value setting for V-line shading [B3] -512 ~ 511 -10 [-4]
28 Correction value setting for V-line shading [B4] -512 ~ 511 -16 [-4]