- 92 -
Control Port Functions
Pin Function Name Function Pol. Action
6 TX_SLOT UART for Slot O
7 RX_SLOT UART for Slot I
8 TRM_1 D_SUB75 ohm terminate ON/OFF O L:Off(Default)H:On
9 TRM_2 D_SUB75 ohm terminate ON/OFF O L:Off(Default)H:On
10 LAMP2_REP_LED Lamp-2Replace LED On/Off O L:LED on
11 C_ON PC Root C Filter ON/OFF O L:Off(Default)H:On
12 GND - -
13 M_OUT Monitor Output ON/OFF O
14 READY_LED Ready LED On/Off O L:LED on
15 TEMP_LED Temp LED On/Off O L:LED on
16 LAMP1_REP_LED Lamp-1 Replace LED On/Off O L:LED on
17 M_SHUTTER_LED Shutter LEDOn/Off O L:LED on
18 FILTER LED Filter LED On/Off O L:LED on
19 PRODUCT_OPT1 Product Option I H
20 PRODUCT_OPT2 Product Option I H
21 S_SW S-Terminal Detection I L:S-Input On
22 W_SW Wired RC Detection Input(5V Input) I L: Wired RC Connected
23 S3.3V - -
24 X1 (Not used) I H Fixed
25 GND - -
26 X2 (Not used) O Open
27 A0 Address 0 I -
28 A1 Address 1 I -
29 A2 Address 2 I -
30 A3 Address 3 I -
31 A4 Address 4 I -
32 CLOCK Clock Input(9.8304MHz) I -
33 S3.3V - -
34 BALAST_SW1_EX Light on LAMP1 O L:OnH:Off
35 BALAST_SW2_EX Light on LAMP2 O L:OnH:Off
36 PFC_SW_EX Power Control O
37 SLOT_SEL Slot1/2 Switch O
38 D0 Data Bus 0 B -
39 D1 Data Bus 1 B -
40 D2 Data Bus 2 B -
41 D3 Data Bus 3 B -
42 GND - -
43 RD Read Signal I -
44 CS4_IOEXP2 Chip Enable I -
45 WE0 Write Signal I -
46 LAMP1_SEL1 Lamp Type Detection I SEL1,2 = L,L:300WL,H:200WH,L:100WH,H:Not define
47 LAMP1_SEL2 Lamp Type Detection I SEL1,2 = L,L:300WL,H:200WH,L:100WH,H:Not define
48 LAMP2_SEL1 Lamp Type Detection I SEL1,2 = L,L:300WL,H:200WH,L:100WH,H:Not define
49 LAMP2_SEL2 Lamp Type Detection I SEL1,2 = L,L:300WL,H:200WH,L:100WH,H:Not define
50 AUDIO_MUTE n/a
51 SHUTTER_SW Shutter Drive Sorenide Power On/Off O L:Off H:On
52 GND - -
53 SMOKE_POW_SW Power for Smoke O HOn L:Off
54 S_P_0 SH-PW Output Signal O
55 S3.3V - -
56 S3.3V - -
57 MODE0 Port Mode Select I L fixed
58 MODE1 Port Mode Select I L fixed
59 DEV0 Division Signal I Switch (Initial:L)
60 DEV1 Division Signal I Switch (Initial:L)
61 GND - -
62 RESET Reset Input Signal I H Reset
63 GND - -
64 S3.3V Analog Power - -
65 ZOOM_POS Zoom Position Detection(A/D Input) AI
66 FOCUS_POS Focus Position Detection(A/D Input) AI
67 TEMP_LCD Temp. Detection arround Panel by thermistor(A/D Input) AI
68 (Not used) (A/D Input) AI
69 (Not used) (Analog Reference) AO (Open)
70 GND Analog Ground - -
71 Select Clock Select I H Fixed
To Next Page
Loading...
