Sanyo PLC-XR201 - XGA LCD Projector

44
Setting
Note:
 •Auto Keystonecorrectsverticaldistortiononly,
notcorrecthorizontaldistortion.
 •TheAutoKeystonefunctioncannotworkwhen
theCeilingfeatureissetOnintheSettingmenu
(p.49).
 •Perfectcorrectionoftheimagedistortioncannot
beensuredwiththeAutosetupfunction.Ifthe
distortionisnotcorrectedproperlybypressingthe
AUTOSETUPortheAUTOSETbutton,adjust
manuallybypressingtheKEYSTONEbuttonon
theremotecontrolorselectingKeystoneinthe
Settingmenu(pp.23,45).
 •Fine sync,Total dots,HorizontalandVertical
positionofsomecomputerscannotbefully
adjustedwiththeAutoPCAdjustmentfunction.
Whentheimageisnotprovidedproperlywith
thisoperation,manualadjustmentsarerequired
(pp.30-31).
Auto setup
Input search
Thisfunctiondetectstheinputsignalautomatically.When
asignalisfound,thesearchwillstop.UsethePoint▲▼
buttonstoselectoneofthefollowingoptions.
Off...........Inputsearchwillnotwork.
On1..........Inputsearchworksunderthefollowingsituation.
 –WhenpressingtheAUTOSETUPbuttonon
thetopcontrol.
 –When pressing theAUTO SET button on the
remotecontrol.
On2..........Inputsearchworksunderthefollowingsituation.
 –Whenturningontheprojectorbypressingthe
ON/STAND-BYbuttononthetopcontrolorthe
remotecontrol.
 –When pressing theAUTO SET button on the
remotecontrol.
 –When pressing the AUTO SETUP button on
thetopcontrol.
 –Whenthecurrentinputsignaliscutoff.*
*IftheNoshoworFreezefunctionisactive,cancelitto
activatetheInputsearch.Itisalsounavailablewhen
On-Screenmenuisdisplayed.
Auto PC adj.
On........Enables Auto PCAdjustment when pressing
theAUTOSETbuttonontheremotecontrolor
theAUTOSETUPbuttononthetopcontrol.
Off.......DisablesAutoPCAdjustment.
Auto Keystone
Auto
. . . . . Alwaysworksandcorrectskeystonedistortion
accordingtotheprojector'stilt.
Manual....WorksonlywhenpressingtheAUTOSETUP
buttononthetopcontrolortheAUTOSET
buttonontheremotecontrol.
Off.......DisablesAutoKeystone.
Auto setup
Note:

•WhileInput searchissettoOn1orOn2,thestatusofInput
andLamparedisplayedeverytimethesignalisswitched.
 •Onlythelastselectedinputsourcecanbedetected.
 •DuringInput searchisinprogress,IftheMENUbuttonor
theON/STAND-BYbuttonispressed,Input searchwillstop.
IftheCOMPUTER1/2buttonorVIDEOorCOMPONENTor
S-VIDEObuttonispressed,Input searchwillstopandgo
backtothebutton'sinputsignal.
 •Input search,Auto PC adj.andAuto Keystonecannotbe
setOffatthesametime.
ThisfunctionenablesInputsearch,AutoKeystonecorrection
andAutoPCadjustmentbypressingtheAUTOSETUPbutton
onthetopcontrolortheAUTOSETbuttonontheremote
control.Settingsforthosefunctionscanbealteredasfollows: