EasyManuals Logo

Sanyo PLC-XU300 User Manual

Sanyo PLC-XU300
79 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #6 background imageLoading...
Page #6 background image
6
Safety Instructions
Openings in the cabinet are provided for ventilation. To
ensure reliable operation of the product and to protect it
from overheating, these openings must not be blocked
or covered.
CAUTION
Hot air is exhausted from the exhaust vent. When using
or installing the projector, the following precautions
should be taken.
– Do not put any flammable object or spray can near the
projector, hot air is exhausted from the air vents.
– Keep the exhaust vent at least 3’ (1 m) away from any
objects.
Do not touch a peripheral part of the exhaust vent,
especially screws and metallic parts. These areas will
become hot while the projector is being used.
Do not put anything on the cabinet. Objects put on the
cabinet will not only get damaged but also may cause
fire hazard by heat.
Cooling fans are provided to cool down the projector.
The fans’ running speed is changed according to the
temperature inside the projector.
CAUTION IN CARRYING OR TRANSPORTING
THE PROJECTOR
– Do not drop or bump the projector, otherwise damages
or malfunctions may result.
When carrying the projector, use a suitable carrying case.
Do not transport the projector by courier or any other
transport service in an unsuitable transport case. This
may cause damage to the projector. For information
about transporting the projector by courier or any other
transport service, consult your dealer.
Do not put the projector in a case before the projector is
cooled enough.
Moving the Projector
When moving the projector, replace the lens cap and
retract adjustable feet to prevent damage to the lens and
cabinet.
When the projector is not in use for an extended period,
put it into a suitable case with the lens side up.
Air Circulation
Air Intake Vent
Air intake Vent
Exhaust Vent
(Hot air exhaust)
Air Intake Vent
Do not tilt the projector more than 30
degrees from above and below.
Do not point the projector up to project an
image.
Do not point the projector down to project
an image.
Do not put the projector on either side to
project an image.
Install the projector properly. Improper Installation may
reduce the lamp life and cause a fire hazard.
Installing the Projector in Proper Position
Exhaust Vent
(Hot air exhaust)
Do not tilt the projector more than 20
degrees from side to side.
20°
20°
30°
30°

Table of Contents

Other manuals for Sanyo PLC-XU300

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC-XU300 and is the answer not in the manual?

Sanyo PLC-XU300 Specifications

General IconGeneral
Vertical scan range50 - 100 Hz
Horizontal scan range15 - 100 kHz
Projection technologyLCD
Contrast ratio (typical)500:1
Screen size compatibility- \
Projector native resolutionXGA (1024x768)
Keystone correction, vertical±30 °
FocusManual
Digital zoom16 x
Aspect ratio4:3
RS-232 ports1
CompatibilityU-XGA S-XGA S-XGA+ W-XGA XGA S-VGA VGA Mac
Dimensions (WxDxH)326 x 231.6 x 92.6 mm
Power requirements100 - 240 V
F-number (relative aperture)1.60
Lamp typeUHP
Lamp power225 W
Light source typeLamp
Service life of light source2000 h
Service life of light source (economic mode)2500 h
Headphone outputs2
Serial interface typeRS-232
Power consumption (standby)3.2 W
Power consumption (typical)287 W
Storage temperature (T-T)-10 - 60 °C
Operating temperature (T-T)5 - 35 °C
Weight and Dimensions IconWeight and Dimensions
Weight2600 g
Package weight5400 g

Related product manuals