Need help?Do you have a question about the Schiedel CM03 and is the answer not in the manual?
Defines the two possible failsafe directions (CW and CCW) for the actuator.
Explains how to find and use the actuator's serial number for identification.
Details the protection class rating of the actuator and its implications.
Provides guidance on the recommended mounting positions for the actuator.
Explains the standard and alternative directions of rotation for the actuator.
Outlines the protective devices integrated into the actuator.
Specifies the acceptable ambient temperature range for actuator operation.
Describes the state of the actuator upon delivery and initial checks.
Details the information provided on the actuator's identification tag.
Covers the procedure for physically connecting the actuator to the valve.
Provides general information and technical data before commissioning.
Describes how to operate the actuator manually using the handwheel.
Covers the default mechanical settings and preparation steps.
Guides on how to set the electrical and mechanical end positions.
Explains the adjustment procedure for the mechanical end stop.
Details how to adjust the failsafe speed of the actuator.
Outlines the final steps after commissioning and adjustments.
Describes the components and functions of the actuator's operating unit.
Explains the graphic and LED display elements used for status information.
Details how to operate the actuator using switches and interfaces.
Covers welcome menu, settings, operation modes, configuration, and TEACHIN function.
Lists the technical data for the CM03F(S)QT failsafe brake.
Lists the technical data for the CM06F(S)QT failsafe brake.
Lists the technical data for the CM12F(S)QT failsafe brake.
Details the specific lubrication points and quantities for F(S)QT actuators.
Outlines the basic service intervals for actuator lubrication based on operating conditions.
Describes the different operating modes for the CM03 F(S)QT actuator.
Describes the different operating modes for the CM06 F(S)QT actuator.
Provides a general overview and identification of the actuator components.
Explains how to identify the actuator using its serial number and type label.
Details the actuator's suitability for different operating modes (open/closed-loop, continuous).
Specifies the actuator's protection class and conditions for its effectiveness.
Offers advice on optimal mounting positions, especially for outdoor use.
Defines the standard directions of rotation for opening and closing the valve.
Outlines the integrated protection devices such as torque monitoring.
Specifies the operating temperature ranges for different actuator types.
Describes the final inspection and delivery status of the actuators.
Details the information provided on the actuator's identification tag.
Mentions silica gel in the connection compartment and its removal.
Provides measures to prevent damage during actuator storage.
Gives instructions for storing actuators for periods longer than six months.
Details the procedure for physically connecting the actuator to the valve.
Explains how to adjust the mounting position of the actuator's control unit.
Provides instructions for making electrical connections, including power supply.
General notes and requirements before starting the commissioning process.
Describes how to operate the actuator manually using its handwheel assembly.
Covers mechanical settings and preparation before motorised operation.
Explains user levels and their permissions for parameter access.
Guides on setting the actuator's end limits for OPEN and CLOSE positions.
Outlines the final steps after commissioning, including checks and sealing.
Describes the components and functions of the actuator's operating unit.
Explains the graphic and LED display elements used for status information.
Details how to operate the actuator using switches and interfaces.
Covers welcome menu, settings, operation modes, configuration, and TEACHIN function.
Covers parameters for configuring end positions and switch-off behavior.
Details parameters related to torque settings for actuator operation.
Explains parameters for setting actuator speed in different modes.
Covers parameters for setting the motor start ramp.
Details parameters related to control functions like ready delay and auxiliary output.
Explains user levels and their impact on parameter access and modification.
Covers parameters for defining intermediate and emergency positions.
Details the configuration and function of the actuator's binary inputs.
Explains the configuration and function of the actuator's binary outputs.
Covers parameters for setting up the analog position output.
Details parameters for setting up step mode operation for extended travel.
Explains parameters for the optional positioner function.
Details parameters for the optional PID controller function.
Covers parameters for enabling torque, speed, and valve characteristic curves.
Allows entering custom identification parameters like PPS number.
Covers parameters for actuator configuration and service information.
Includes parameters for language, smartcode, backup, and info display.
Shows default user level settings for parameters, controlling access and modification.
Presents current process, diagnostic data, and status of outputs and inputs.
Shows logged history entries, including warnings, errors, and status changes.
Lists all possible history entries with their types and descriptions.
Lubricant recommendations for the main body within a specific temperature range.
Lubricant recommendations for the main body at lower temperatures.
Lubricant recommendations for output type A and spindle drives.
Outlines the basic service intervals for actuator lubrication based on operating conditions.
Provides technical specifications for the actuator's binary outputs.
Provides technical specifications for the actuator's binary inputs.
Details the specifications for the analog inputs of the actuator.
Provides technical specifications for the analog output of the actuator.
Lists technical data for auxiliary voltage inputs and outputs.
Describes the types of connections for explosion-proof and non-explosion-proof versions.
Details the various modes of operation for CM actuators.
Specifies the operating modes for CM03 + QT actuator variants.
Outlines the operating modes for CM03 + L actuator variants.
Details the operating modes for CM03 + LK actuator variants.
Covers miscellaneous technical specifications like ambient temperature and color.
Provides technical specifications for the standard CM03 actuator.
Lists technical data for the 24 VDC version of the CM03 actuator.
Details technical data for the 400 V version of the CM03 actuator.
Provides technical specifications for the standard CM06 actuator.
Lists technical data for the 400V version of the CM06 actuator.
Provides technical specifications for the standard CM12 actuator.
Displays characteristic curves for the CM03 actuator.
Displays characteristic curves for the CM06 actuator.
Displays characteristic curves for the CM12 actuator.
General| Brand | Schiedel |
|---|---|
| Model | CM03 |
| Category | Fireplace Accessories |
| Language | English |
To Next Page