SEA GATE 2 - TRANSMITTER PROGRAMMING; Transmitter Compatibility Warning; Programming Transmitter on Start; Programming Transmitter on Partial Start

GATE 2
PROGRAMMING A TRANSMITTER
WARNING: The default card will only accept ROLLING CODE radio transmitters (Ladbird Roll and and Smart Roll)
associated with the RF ROLL (433 Mhz Code 23120470, 868 Mhz Code 23120480). To program “NOT ROLLING
CODE” transmitters (Smart Dual, Ladybird Dip and Copy and Head) it is necessary to replace the microprocessor
with the appropriate kit (Code 23120419) and to insert on the control unit the RF module (433 Mhz Cod.23120420, 868
Mhz Cod . 23120425).
Note: The RF ROLL receivers will be manageable with the SP40 management software (Code 23105295) and with the
OPEN sytem (Code 23105290).
PROGRAMMING A TRANSMITTER ON START
Press button P2 (PCode) until LEDP turns ON.
If no further code is memorized within 10 seconds, the LED automatically goes OFF and exits the programming procedure.
ATTENTION: If the code entered is already in the memory, it will be deleted. LedP flashes 4 times to confirm this procedure.
PROGRAMMING A TRANSMITTER ON PARTIAL START
1) Press button P2 (PCode) until LEDP turns ON.
2) Press button P1 (PTime). LEDP will start to flash quickly
If no further code is memorized within 10 seconds, the LED automatically goes OFF and exits the programming procedure.
ATTENTION: If the code entered is already in the memory, it will be deleted. LedP flashes 4 times to confirm this procedure.
CANCELLATION OF ALL RADIO TRANSMITTERS
Press and keep pressed button Pcode, ledP will start to flash. Wait until the ledP stops to flash and release the Pcode. LedP
will flash 6 times to confirm the cancellation.
Give a START with the transmitter, using the button chosen for the start
command.
The LED will flash twice to confirm that the transmitter code has been memorized
and will remain ON waiting for further transmitters.
Give a START with the transmitter, using the button chosen for the start
command.
The LED will flash twice to confirm that the transmitter code has been memorized
and will remain ON waiting for further transmitters.
P2
LEDP
P1
LEDP
LEDP
1) 2)
20
International registered trademark n. 2.777.971
P2P2
P2
LEDP
LEDP
U1U1
U2U2
RV1RV1
RV2RV2
RV3RV3
P1P1
P2P2
F1F1
F2F2
CN1CN1
CN2CN2 CN3CN3
R
L
1
R
L
1
R
2
L
R
2
L
R
L
3
R
L
3
LD
E
1
LD
E
1
LE
D
2
LE
D
2
L
E
D
3
L
E
D
3
E
L D
4
E
L D
4
LE
D
5
LE
D
5
LD
6
ELD
6
E
7
L
ED
7
L
ED
EL
D
8
EL
D
8
E
L 9
D
E
L 9
D
1
L
E
D
01
L
E
D
0
L
ED
11L
ED
11
L D
12
EL D
12
E
E
1
L
D
3
E
1
L
D
3
L D
14
EL D
14
E
1
LE
D 5
1
LE
D 5
EL
D
1
6
EL
D
1
6
DIPDIP
T1T1
CN4CN4
L
DPEL
DPE
REV 05 - 10/2010