Sharp MX-5000N - Page 274

MX-5001N SIMULATION 6 – 127
63-4
Purpose
Adjustment/Setting/Operation data check
Function (Purpose)
Used to display the SIT chart patch density.
Section
Operation/Procedure
1) Set the SIT chart (UKOG-0280FCZZ or UKOG-0280FCZ1) to
the reference position on the left rear frame side of the docu-
ment table.
2) Select [OC] key or [DSPF] key. ([DSPF] key can be selected
only when the DSPF is installed.)
3) Press [EXECUTE] key.
The patch of the SIT chart is scanned.
When the operation is completed, [EXECUTE] key returns to
the normal display.
4) Select a data display mode.
Select an target display color with [R] [G] [B] keys.
63-5
Purpose
Adjustment/Setup
Function (Purpose)
Used to perform the scanner (CCD) color
balance and gamma default setting.
Section
Operation/Procedure
1) Select [SIDE A(OC)] key or [SIDE B(DSPF)] key. ([SIDE
B(DSPF)] key can be selected only when the DSPF is
installed.)
2) Press [EXECUTE] key, and press [OK] key
3) The scanner (CCD) color balance and gamma are set to the
default.
63-6
Purpose
Adjustment/Setting/Operation data check
Function (Purpose)
Used to display the scan level and the den-
sity level of the copy color balance adjust-
ment patch.
Section
Operation/Procedure
1) Set the color balance adjustment pattern sheet printed with
SIM46-21 on the document table.
2) Press [EXECUTE] key.
The patch image of the adjustment pattern sheet is scanned.
Select a target color with [C] [M] [Y] [K] key.
63-7
Purpose
Adjustment/Setup
Function (Purpose)
Used to register the service target of the
copy mode auto color balance adjustment.
Section
Operation/Procedure
1) Press [SETUP] key on the touch panel.
2) Set the color balance adjustment pattern sheet printed with
SIM46-21 on the document table.
3) Press [EXECUTE] key.
The patch image of the adjustment pattern sheet is scanned.
4) Press [OK] key.
The service target of the copy mode automatic color balance
adjustment is registered according to the patch image of the
scanned adjustment pattern sheet.
The registered color balance and the density are displayed.
Select a target color with [C] [M] [Y] [K] key.
NOTE: This simulation is executed only when the copy color bal-
ance is manually adjusted.
THROUGH GAMMA SIT chart scan data
COPY GAMMA Copy mode gamma process data of the
SIT chart scan data
SCANNER GAMMA Image send mode gamma process data of
the SIT chart scan data
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
3$7&+'$7$',63/$<2)6&$11(5&2/25%$/$1&(



(;(&87(
2&



&&&555
000***
<<<%%%
% * 5
2&㪛㪪㪧㪝
ǂǂǂ6,08/$7,21
ǂǂ12
&/26(
7(67
67$1'$5'6&$11(5*$00$6(783




6,'($2&
$5(<28685("
<(6 12 (;(&87(
6,'(%'63)
B Point B target value
C Point C target value
D Point D target value
E Point E target value
F Point F target value
G Point G target value
H Point H target value
I Point I target value
J Point J target value
K Point K target value
L Point L target value
M Point M target value
N Point N target value
O Point O target value
BASE Background sampling value
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(&2/25%$/$1&(&+$575($',1*


(;(&87(
6(77+(&+$57213/$7(1$1'728&+>(;(&87(@