MX-5001N ADJUSTMENTS 5 – 9
4-C Transfer voltage adjustment
This adjustment is needed in the following situations:
* When the primary transfer high voltage power PWB or Second-
ary transfer high voltage power PWB is replaced.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
1) Go through the modes specified in Simulation 8-6.
2) Select a mode to be adjusted with the scroll key.
3) Enter an adjustment value (specified value) and press [OK]
key.
By setting the default value (specified value), the specified
voltage is outputted.
When [EXECUTE] key is pressed, the transfer voltage is out-
putted.
EXECUTE
EXECUTE
or after 30 sec.
10-key
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
7+96(77,1*$1'287387
$˖
˷˹
˖7&/2:63(('&/.
$˖
˖7&0,''/(63(('&/.
%˖
˖7&/2:63(('&/&
&˖
˖7&0,''/(63(('&/&
'˖
˖7&0,''/(63(('&/0
)˖
˖7&/2:63(('&/0
(˖
˖7&/2:63(('&/<
*˖
˖7&0,''/(63(('&/<
+˖
˖7&/2:63(('%:.
,˖
˖7&0,''/(63(('%:.
-˖
˖7&3/$,1&/63;
.˖
˖7&3/$,1&/'3;
/˖
2.
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
7+96(77,1*$1'287387
$˖
˷˹
˖7&/2:63(('&/.
$˖
˖7&0,''/(63(('&/.
%˖
˖7&/2:63(('&/&
&˖
˖7&0,''/(63(('&/&
'˖
˖7&0,''/(63(('&/0
)˖
˖7&/2:63(('&/0
(˖
˖7&/2:63(('&/<
*˖
˖7&0,''/(63(('&/<
+˖
˖7&/2:63(('%:.
,˖
˖7&0,''/(63(('%:.
-˖
˖7&3/$,1&/63;
.˖
˖7&3/$,1&/'3;
/˖
2.
(;(&87(
Item/Display Content
Setting
range
Default value
Actual output
setting range
Default
value of
actual
output
value
41-sheet
machine
50-sheet
machine
A TC1 LOW SPEED CL K Primary transport
bias reference
value
Color K In low speed 51 - 255 95 2µA - 30µA8µA
B TC1 MIDDLE SPEED CL K In middle
speed
146
182 15µA
C TC1 LOW SPEED CL C C In low speed 95 8µA
D TC1 MIDDLE SPEED CL C In middle
speed
146 15µA
E TC1 LOW SPEED CL M M In low speed 95 8µA
F TC1 MIDDLE SPEED CL M In middle
speed
146 15µA
G TC1 LOW SPEED CL Y Y In low speed 95 8µA
H TC1 MIDDLE SPEED CL Y In middle
speed
146 15µA
I TC1 LOW SPEED BW K Black/
White
K In low speed 95 8µA
J TC1 MIDDLE SPEED BW K In middle
speed
146
182 15µA
1
1
: Oct. 24 2008
1
To Next Page
Loading...
