Home
Shelly
Switch
Wave 1PM
Shelly Wave 1PM User Manual
5
of 1
of 1 rating
32 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
EN
.
30
14.
Technical Specificatio
ns
Power supply
110
-240 V AC / 24
–
30 V DC
Power consumption
< 0.3 W
Power measurement (W)
Yes
Max switching voltage AC
240 V
Max switching current AC
16 A
Max switching voltage DC
30 V
Max switching current DC
10 A
Overheating protection
Yes
Overload protection
Yes
Distance
Up to 40 m indoors (131 ft.)
(depends on local condition)
Z-Wave
™
repeater:
Yes
CPU
Z-Wave
™
S800
Z-Wave
™
frequency bands:
868,4 MHz; 865,2 MHz; 869,0
MHz; 921,4 MHz; 908,4 MHz;
916 MHz; 919,8 MHz; 922,5
MHz; 919,7-921,7-923,7 MHz;
868,1 MHz; 920,9 MHz
Maximum radio frequency
power transmitted in
frequency band(s)
< 25 mW
Size (H x W x D)
37x42x16 ±0.5 mm /
1.46x1.65x0.63 ±0.02 in
Weight
27 g / 0.95 oz.
Mounting
Wall console
Screw terminals max. torque
0.4 Nm / 3.5 lbin
Conductor cross section
0.5 to 1.5 mm² / 20 to 16 AWG
Conductor stripped length
5 to 6 mm / 0.20 to 0.24 in
Shell material
Plastic
29
31
Table of Contents
Default Chapter
2
Table of Contents
2
1 Terminology and Abbreviations
4
2 About Shelly Qubino
4
3 About the Device
4
4 Electrical Diagrams (110-240 V AC / 24-30 V DC)
5
Installation Instruction
6
5 About Z-Wave
8
6 Z-Wave™ Adding / Removing / Factory Reset
9
Adding the Device to a Z-Wave™ Network (Inclusion)
9
Smartstart Adding (Inclusion)
9
Adding (Inclusion) with a Switch/Push-Button
9
3Adding (Inclusion) with the S Button
10
Removing the Device from a Z-Wave™ Network (Exclusion)
10
Removing (Exclusion) with a Switch/Push-Button
10
Removing (Exclusion) with the S Button
11
Factory Reset
11
Factory Reset General
11
Factory Reset with a Switch/Push-Button
11
Factory Reset with the S Button
11
Remote Factory Reset with Parameter with the Gateway
12
7 Z-Wave™ Security 2 and Device Specific Key (DSK)
13
8 LED Signalization
15
General Rules
15
9 Z-Wave™ Parameters
17
Parameter No. 1 - SW (SW1) Switch Type
17
Parameter No. 17 - Restore State of O (O1) after Power Failure
17
Parameter No. 19 - O (O1) Auto off with Timer
17
Parameter No. 20 - O (O1) Auto on with Timer
18
Parameter No. 23 - O (O1) Contact Type - NO/NC
18
Parameter No. 25 - Set Timer Units to S or Ms for O (O1)
19
Parameter No. 36 - O (O1) Power Report on Change - Percentage
19
Parameter No. 39 - Minimum Time between Reports (O) O1
19
Parameter No. 91 - Water Alarm
20
Parameter No. 92 - Smoke Alarm
20
Parameter No. 93 - CO Alarm
20
Parameter No. 94 - Heat Alarm
21
Parameter No. 120 - Factory Reset
21
Parameter No. 201 - Serial Number 1
22
Parameter No. 202- Serial Number 2
22
Parameter No. 203 - Serial Number 3
22
10 Z-Wave™ Command Class
24
11 Z-Wave™ Notifications Command Class
26
Overheat Detected
26
Overcurrent Detected O
26
AC Mains Disconnected
27
12 Z-Wave™ Associations
28
Root Device
28
13 Supported Load Types
29
14 Technical Specifications
30
15 Important Disclaimer
32
16 Declaration of Conformity
32
17 Manufacturer
32
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Shelly Wave 1PM and is the answer not in the manual?
Ask a question
Shelly Wave 1PM Specifications
General
Brand
Shelly
Model
Wave 1PM
Category
Switch
Language
English
Related product manuals
Shelly Wave 1
30 pages
Shelly Wave Pro 1
28 pages
Shelly Button
12 pages
Shelly button1
2 pages
Shelly PRO 2
19 pages
Shelly PRO 4PM
2 pages