Siemens Sinumerik 840 sl Configuration Manual

12.95
Index-140
E Siemens AG, 2002. All rights reserved
SINUMERIK 810D Manual Hardware Configuration (PHC) -- 11.02 Edition
Installing the SINUMERIK 810D, 3-42
Integrated power sections, 4-77, 4-79
Interconnecting cables, 1-19, 4-72
Interfaces for servicing/installation and
start--up/maintenance, 2-29
Interfaces of the SINUMERIK 810D, 4-54
Interfaces, description, 4-56
L
L2 DP interface, X102, 4-57
Labeling, 1-23
M
Mains supply, 3-49
Maintenance, 9-117
Measuring channels, 4-72
Measuring system, 4-69
Measuring system, direct, FDD, 4-74
Measuring system, direct, MSD, 4-76
Measuring system, indirect, FDD, 4-72
Measuring system, indirect, MSD, 4-75
Mechanical data, 2-37
Modification for external mounting, 2--axis CCU
box, 3-47
Motor connection, 4-69
Motor leads, connection, 3-48
Motor measuring system, 4-69
MPI connector, 2-38
MPI interconnecting cables, 2-38
MPI interface, X122, 4-59
MPI network rules, 2-39
N
NCU terminal block, 7-97
Connection, 7-98
DMP compact modules, 7-98
EMC measures, 7-98
Monitoring functions, 7-99
Power supply, 7-100
Protective conductor, 7-98
Terminator, 7-98
X11--X18, 7-100
X20/X21, 7-100
Noise immunity, 2-26
Noise immunity of the complete system, 2-32
O
Operating conditions, 2-35
P
PCMCIA card (memory c ard), 4-80
PLC module, 4-80
Position of the interfaces, 4-56
Position of the interfaces on the CCU3, 4-64
Position sensing, direct, FDD, 4-74
Position sensing, indirect FDD, 4-73
Power consumption, 2-28
Power modules, 1-20
Power supply, 2-27
powerline, SINUMERIK 810D/810DE, 1-13
powerline modules, SINUMERIK 810D/810DE,
1-13
PS/2, Mouse, 1-17
R
Radio interference, 2-26
Rated load cycles FDD, 4-77, 4-79
Rated load cycles MSD, 4-78
Relative air humidity, 2-34, 2-35, 7-101
Restrictions for 611D standard closed-loop
control, 4-52, 4-53
RI suppression measures, 2-32
Ribbon cable, 5-85
Ribbon cable connectors, 5-84
S
Safe electrical isolation, 2-29
Secondary conditions, electrical, 2-25
Secondary electrical conditions, 2-25
Service, 9-117
Shield plate, attachment, 3-45
Shielded signal cables, 2-32
Shock load, 2-36
Signal chart for incremental encoders, 4-70
Simultaneity factor (GZF), 4-78
Single I/O module, 6-89
Address space, 6-95
Connection, 6-89
Dimension drawing, 6-90
Electronics power supply, 6-92
EMC, 6-90
Inputs/outputs, 6-93
LED, 6-93
Load power supply, 6-92
Technical data, 6-91
X402, 6-93
X404, 6-94
X405, 6-94
SINUMERIK 810D powerline, v, 1-13
Storage conditions, 2-34
11.02

Siemens Sinumerik 840 sl Specifications

General

Brand	Siemens
Model	Sinumerik 840 sl
Category	Control Unit
Language	English