Siemens SINUMERIK MCP-S Series - Page 43

1 2 3 4 5 6 7 8 9 10 Meaning
o󹪜 on o󹪜 on o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn10
on o󹪜 o󹪜 on o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn9
o󹪜 o󹪜 o󹪜 on o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn8
on on on o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn7
o󹪜 on on o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn6
on o󹪜 on o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn5
o󹪜 o󹪜 on o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn4
on on o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn3
o󹪜 on o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn2
on o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn1
o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 Default device name: mcp-pn
MCP set up as IE
Table 5-13 Switch S2 is set as delivered
1 2 3 4 5 6 7 8 9 10 Meaning
o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 o󹪜 on on o󹪜 o󹪜 MCP address 192
The two switches S1-9 and S1-10 must remain set to "o󹪜" (IE functionality).
The switches S1-1 to S1-8 de󹪝ne the MCP address in the range of 0 to 255.
The addresses from 192 to 223 count as the default range.
The MCP address is used as a reference for addressing an MCP during the PLC parameter
assignment.
Table 5-14 Settings of switch S1
1 2 3 4 5 6 7 8 9 10 Meaning
o󹪜 o󹪜
on on on on on on on on MCP address 255
x x x x x x x x "
on on on on on o󹪜 on on MCP address 223
o󹪜 on on on on o󹪜 on on MCP address 222
on o󹪜 on on on o󹪜 on on MCP address 221
o󹪜 o󹪜 on on on o󹪜 on on MCP address 220
on on o󹪜 on on o󹪜 on on MCP address 219
o󹪜 on o󹪜 on on o󹪜 on on MCP address 218
on o󹪜 o󹪜 on on o󹪜 on on MCP address 217
o󹪜 o󹪜 o󹪜 on on o󹪜 on on MCP address 216
on on on o󹪜 on o󹪜 on on MCP address 215
o󹪜 on on o󹪜 on o󹪜 on on MCP address 214
Connecting
5.1 interfaces
ONE MCP Part 1: MCP xxxx
Equipment Manual, 07/2020, A5E50324729B AA 43