Siemens SIPROTEC 7RW80 User Manual

Appendix
A.7 Settings
SIPROTEC, 7RW80, Manual
C53000-G1140-C233-1, Release date 10.2010
230
5588 LR4 after 81-1 Load Restore YES
NO
NO Load restoration element 4 after 81-
1
5589 LR4 after 81-2 Load Restore YES
NO
NO Load restoration element 4 after 81-
2
5590 LR4 after 81-3 Load Restore YES
NO
NO Load restoration element 4 after 81-
3
5591 LR4 after 81-4 Load Restore YES
NO
NO Load restoration element 4 after 81-
4
6101 Synchronizing SYNC function 1 ON
OFF
OFF Synchronizing Function
6102 SyncCB SYNC function 1 (Setting options depend
on configuration)
None Synchronizable circuit breaker
6103 Vmin SYNC function 1 20 .. 125 V 90 V Minimum voltage limit: Vmin
6104 Vmax SYNC function 1 20 .. 140 V 110 V Maximum voltage limit: Vmax
6105 V< SYNC function 1 1 .. 60 V 5 V Threshold V1, V2 without voltage
6106 V> SYNC function 1 20 .. 140 V 80 V Threshold V1, V2 with voltage
6107 SYNC V1<V2> SYNC function 1 YES
NO
NO ON-Command at V1< and V2>
6108 SYNC V1>V2< SYNC function 1 YES
NO
NO ON-Command at V1> and V2<
6109 SYNC V1<V2< SYNC function 1 YES
NO
NO ON-Command at V1< and V2<
6110A Direct CO SYNC function 1 YES
NO
NO Direct ON-Command
6111A TSUP VOLTAGE SYNC function 1 0.00 .. 60.00 sec 0.10 sec Supervision time of V1>;V2> or
V1<;V2<
6112 SYN. DURATION SYNC function 1 0.01 .. 1200.00 sec; ∞ 30.00 sec Maximum duration of synchronism-
check
6113A 25 Synchron SYNC function 1 YES
NO
YES Switching at synchronous condition
6121 Balancing V1/V2 SYNC function 1 0.50 .. 2.00 1.00 Balancing factor V1/V2
6122A ANGLE ADJUSTM. SYNC function 1 0 .. 360 ° 0 ° Angle adjustment (transformer)
6123 CONNECTIONof V2 SYNC function 1 A-B
B-C
C-A
A-B Connection of V2
6125 VT Vn2, primary SYNC function 1 0.10 .. 800.00 kV 20.00 kV VT nominal voltage V2, primary
6150 dV SYNCHK V2>V1 SYNC function 1 0.5 .. 50.0 V 5.0 V Maximum voltage difference V2>V1
6151 dV SYNCHK V2<V1 SYNC function 1 0.5 .. 50.0 V 5.0 V Maximum voltage difference V2<V1
6152 df SYNCHK f2>f1 SYNC function 1 0.01 .. 2.00 Hz 0.10 Hz Maximum frequency difference
f2>f1
6153 df SYNCHK f2<f1 SYNC function 1 0.01 .. 2.00 Hz 0.10 Hz Maximum frequency difference
f2<f1
6154 dα SYNCHK α2>α1 SYNC function 1 2 .. 80 ° 10 ° Maximum angle difference
alpha2>alpha1
6155 dα SYNCHK α2<α1 SYNC function 1 2 .. 80 ° 10 ° Maximum angle difference
alpha2<alpha1
8101 MEASURE. SUPERV Measurem.Superv OFF
ON
ON Measurement Supervision
8102 BALANCE V-LIMIT Measurem.Superv 10 .. 100 V 50 V Voltage Threshold for Balance Mon-
itoring
8103 BAL. FACTOR V Measurem.Superv 0.58 .. 0.90 0.75 Balance Factor for Voltage Monitor
8201 FCT 74TC 74TC TripCirc. ON
OFF
ON 74TC TRIP Circuit Supervision
8202 Alarm Delay 74TC TripCirc. 1 .. 30 sec 2 sec Delay Time for alarm
8311 MinMax cycRESET Min/Max meter NO
YES
YES Automatic Cyclic Reset Function
8312 MiMa RESET TIME Min/Max meter 0 .. 1439 min 0 min MinMax Reset Timer
8313 MiMa RESETCYCLE Min/Max meter 1 .. 365 Days 7 Days MinMax Reset Cycle Period
8314 MinMaxRES.START Min/Max meter 1 .. 365 Days 1 Days MinMax Start Reset Cycle in
8315 MeterResolution Energy Standard
Factor 10
Factor 100
Standard Meter resolution
Addr. Parameter Function Setting Options Default Setting Comments

Siemens SIPROTEC 7RW80 Specifications

General

Brand	Siemens
Model	SIPROTEC 7RW80
Category	Relays
Language	English