Sony PDW-700 - Page 180

FTP File Operations
180
Chapter 8 File Operations
<type-code> can be any of the following. However,
for XDCAM, data is always transferred as “I”,
regardless of the type-code specification.
•A: ASCII
- N: Non-print
- T: Telnet format
- C: ASA Carriage Control
• E: EBCDIC
- N: Non-print
- T: Telnet format
- C: ASA Carriage Control
• I: IMAGE (Binary) (default)
• L: LOCAL BYTE
- SIZE: byte size
Input example: TYPE I
STRU
Specifies the data structure.
Syntax: STRU <SP> <structure-code> <CRLF>
<structure-code> can be any of the following.
However, for XDCAM, the structure is always “F”,
regardless of the structure-code specification.
• F: File structure (default)
• R: Record structure
• P: Page structure
Input example: STRU F
MODE
Specifies the transfer mode.
Syntax: MODE <SP> <mode-code> <CRLF>
<mode-code> can be any of the following.
However, for XDCAM, the mode is always “S”,
regardless of the mode-code specification.
• S: Stream mode (default)
• B: Block mode
• C: Compressed mode
Input example: MODE S
LIST
Sends a list of files from this unit to the remote computer.
Syntax: LIST <SP> <options> <SP> <path-name>
<CRLF>
<options> can be any of the following.
• -a: Also display file names that begin with “·”.
• -F: Append “/” to directory names.
The following data is transferred, depending on
whether <path-name> specifies a directory or file.
• Directory specified: A list of the files in the
specified directory
• File specified: Information about the specified
file
• No specification: A list of the files in the current
directory.
The wildcard characters “*” (any string) and “?”
(any character) may be used in <path-name>.
Input example 1: LIST -a Clip
Input example 2: LIST Clip/*.MXF
NLST
Sends a list of file names from this unit to the remote
computer, with no other information.
Syntax: NLST <SP> <options or path-name>
<CRLF>
The following options may be specified when no
path name is specified.
• -a: Also display file names that begin with “.”
• -I: Display information other than file name
(gives the same result as the LIST command).
• -F: Append “/” to directory names.
The following data is transferred, depending on
whether <path-name> specifies a directory or file.
• Directory specified: A list of the file names only
in the specified directory
• No specification: A list of the file names only in
the current directory.
The wildcard characters “*” (any string) and “?”
(any character) may be used in <path-name>.
Input example 1: NLST-I
Input example 2: NLST Clip/*.MXF
RETR
Begins transfer of a copy of a file in the specified path on
this unit to the current directory on the remote computer.
Syntax:RETR <SP> <path-name> <CRLF>
Input example: RETR Clip/C0001.MXF
STOR
Begins transfer of a copy of a file in the specified path on
the remote computer to the current directory on this unit.
Depending on the type of file transferred, the following
items are created.
•C*.MXF file
1), 3)
- C*M01.XML file (metadata)
- C*S01.MXF file (proxy AV data)
- For C*.MXF files, the UMID of the copy source file
is not saved. However, it is saved if an immediately
preceding SITE UMMD extended command has
been issued.
• E*E01.SMI file
2), 3)
- E*M01.XML file (metadata)
1) *: 0001 to 9999